Nissan Primera P12. Instruction — part 453
EM-158
[F9Q]
TIMING BELT
7.
Remove baffle plate. Refer to
.
8.
Remove wiper arms and wiper motor. Refer to
WW-12, "Removal and Installation for Wiper Motor and
or
WW-33, "Removal and Installation for Wiper Motor and Linkage"
(with rain sensor).
9.
Remove bracket as shown.
10. Set the engine support bar and chain (commercial service tool)
or suitable tool, and secure the engine in position.
●
Support bottom of engine by setting a instruction lift table caddy
(commercial service tool) or equivalently tool.
CAUTION:
Put a piece of wood or something similar as the support-
ing surface, secure a completely stable condition.
11. Remove power steering pump bracket mounting bolt and move
the piping.
12. Remove ground cable.
13. Remove RH engine mounting upper bracket bolts. Refer to
.
14. Remove RH engine mounting insulator.
MBIB0977E
MBIB0964E
MBIB0965E
MBIB0966E
TIMING BELT
EM-159
[F9Q]
C
D
E
F
G
H
I
J
K
L
M
A
EM
15. Remove RH engine mounting bracket.
16. Remove front timing belt cover.
17. Obtain compression TDC of No.1 cylinder as follows:
a.
Rotate crankshaft pulley clockwise direction at the timing end.
b.
Once the mark on the camshaft pulley is located half a cog
before the protecting metal sheet push on the TDC setting and
[KV113B0280 (Mot. 1054)] until camshaft is lifted.
18. Remove crankshaft pulley as follows:
NOTE:
Use a pencil to mark the lower timing housing opposite the mark
on the camshaft pulley.
●
Loosen the crankshaft pulley fixing bolts and pull crankshaft
pulley with both hands to remove it. (At this time set a suitable
tool to ring gear so that crankshaft cannot rotate.)
CAUTION:
●
Be careful not to damage the signal plate teeth.
●
Do not remove fixing bolts. Keep loosened fixing bolts
in place to protect removed crankshaft pulley from
dropping.
MBIB0967E
MBIB0968E
MBIB0978E
MBIB0969E
EM-160
[F9Q]
TIMING BELT
19. Slacken the timing belt by loosening the bolt of tensioner, then
remove timing belt.
20. Remove crankshaft sprocket.
21. If necessary, remove front cover.
INSTALLATION
●
Install in the reverse order of removal paying attention to the following.
Front cover
●
Refer to
EM-203, "INSTALLATION OF LOWER ENGINE"
.
Timing Belt
●
Refer to
.
MBIB0970E
CYLINDER HEAD
EM-161
[F9Q]
C
D
E
F
G
H
I
J
K
L
M
A
EM
CYLINDER HEAD
PFP:11041
Removal and Installation
EBS00SKC
CAUTION:
Apply new engine oil to parts marked in illustration before installation.
REMOVAL
1.
Remove the following parts.
●
Battery ground cable
●
Undercover
●
RH front wheel
2.
Remove right side splash cover.
3.
Remove engine room cover. Refer to
.
4.
Drain engine coolant. Refer to
CO-25, "Changing Engine Coolant"
.
CAUTION:
Perform when engine is cold.
5.
Remove air inlet tube from intake manifold. Refer to
.
MBIB0971E
1.
Front engine slinger
2.
Camshaft bearing beam
3.
Camshaft
4.
Timing belt rear cover
5.
Camshaft sprocket
6.
Cylinder head suspended bracket
7.
Shim
8.
Valve rotator
9.
Valve spring retainer
10. Valve spring
11.
Valve cotter
12. Exhaust valve
13. Intake valve
14. Cylinder head gasket
15. Rear engine slinger
16. Engine cover bracket
17. Cylinder head
18. Cylinder head bolt
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст