Nissan Versa Sedan. Instruction — part 833
TM-238
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
CONTROL CABLE
2. Install the socket (A) onto the shift selector assembly.
CAUTION:
• Insert the socket into the shift selector assembly, then
push it firmly in place.
• Check that pulling on the socket does not disconnect it.
Inspection
INFOID:0000000009268021
INSPECTION AFTER INSTALLATION
Check the A/T position. If a malfunction is found, adjust the A/T position. Refer to
.
JSDIA1810ZZ
KEY INTERLOCK CABLE
TM-239
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000009268022
Removal and Installation
INFOID:0000000009268023
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
1. Move the shift selector to the “N” position.
2. Remove the shift selector handle. Refer to
TM-234, "Disassembly and Assembly"
.
3. Remove the center console. Refer to
IP-23, "Removal and Installation"
.
4. Move the shift selector to the “P” position.
5. Press the pawls (B) of the key interlock cable slider (A) while
sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider.
6. Remove the key interlock cable from the shift selector assembly.
7. Remove the instrument lower panel LH. Refer to
8. Remove the steering column upper and lower covers. Refer to
.
9. Remove the center console lower (if equipped). Refer to
1.
A/T shift selector assembly
2.
Key interlock cable
A:
Key cylinder
B:
Lock plate
C:
Clip
ALDIA0262ZZ
(E)
: Key interlock rod
JSDIA1797ZZ
TM-240
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
KEY INTERLOCK CABLE
10. Lift lock plate (A) in the direction of the arrow (
C) and remove
in the direction of the arrow (
D).
11. Remove the key interlock cable from the key cylinder.
12. Disengage the clips and remove the key interlock cable from the
vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• Temporarily install the adjust holder (A) to the key interlock rod (B).
• Install the casing cap (C) to the cable bracket (D) on the shift
selector assembly.
CAUTION:
• Do not bend or twist key interlock cable excessively when
installing.
• After installing key interlock cable to cable bracket (D) on
shift selector assembly, make sure casing cap (C) is firmly
secured in cable bracket (D) on shift selector assembly.
• If casing cap (C) is loose [less than 39.2 N (4.0 kg, 8.8 lb)
removing force], replace key interlock cable.
• Slide the slider (A) toward the key interlock rod (D) while pressing
the pull lock (B) down to securely connect the adjust holder (C)
with the key interlock rod (D).
CAUTION:
• Do not press tabs when holding slider (A).
• Do not apply any side-to-side force to key interlock rod (D)
when sliding slider (A).
Inspection
INFOID:0000000009268024
INSPECTION AFTER INSTALLATION
• Check the A/T operation. If a malfunction is found, adjust the A/T position. Refer to
.
• Make sure the key can be removed only when the shift selector is in the “P” position.
• Make sure the ignition switch will not turn to LOCK position when the shift selector is not in the “P” position.
(1)
: Key interlock cable
(B)
: Key cylinder
JSDIA1798ZZ
JSDIA1799ZZ
JSDIA1800ZZ
TCM
TM-241
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
TCM
Exploded View
INFOID:0000000009268025
Removal and Installation
INFOID:0000000009268026
NOTE:
When replacing the TCM and transaxle assembly as a set, replace the transaxle assembly first and then
replace the TCM. Refer to
REMOVAL
1. Remove the battery. Refer to
PG-63, "Removal and Installation"
2. Disconnect the harness connector from the TCM.
3. Remove the TCM and bracket as an assembly.
4. Remove the TCM from the bracket, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
Adjustment
INFOID:0000000009268027
ADJUSTMENT AFTER INSTALLATION
Perform “ADDITIONAL SERVICE WHEN REPLACING TCM”. Refer to
.
1.
TCM
2.
Bracket
3.
Clips
Front
AWBIA1481ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст