Nissan Versa Sedan. Instruction — part 834
TM-242
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
OIL PAN
OIL PAN
Exploded View
INFOID:0000000009268028
Removal and Installation
INFOID:0000000009268029
REMOVAL
1. Remove the drain plug and overflow tube, and then drain the ATF.
WARNING:
A/T fluid can splash when draining, use safety glasses to protect eyes.
2. Remove the drain plug gasket from the drain plug.
3. Remove the oil pan bolts (
), and then remove the oil pan and
oil pan gasket.
4. Remove the magnets from the oil pan.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse oil pan gasket and drain plug gasket.
1.
Transaxle assembly
2.
Oil pan gasket
3.
Magnet
4.
Oil pan
5.
Overflow tube
6.
Drain plug gasket
7.
Drain plug
8.
Oil pan fitting bolt
JSDIA1932GB
: Front
JSDIA1933ZZ
OIL PAN
TM-243
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Do not reuse oil pan bolts.
• Completely remove all moisture, oil, old gasket, etc. from the oil pan gasket mating surface of tran-
saxle case and oil pan.
• When installing the overflow tube, be sure to tighten to the specified torque. If it is not tightened to
the specified torque, the tube may be damaged.
• When the oil pan is installed, temporarily tighten oil pan bolts, then
tighten the oil pan bolts to specification in the order shown.
Inspection and Adjustment
INFOID:0000000009268030
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check for A/T fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Check the A/T fluid level. Refer to
: Front
JSDIA1934ZZ
TM-244
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
OUTPUT SPEED SENSOR
OUTPUT SPEED SENSOR
Exploded View
INFOID:0000000009268031
Removal and Installation
INFOID:0000000009268032
REMOVAL
1. Remove the front LH wheel and tire.
2. Disconnect the harness connector from output speed sensor.
3. Remove the output speed sensor.
4. Remove the O-ring from the output speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN Matic S ATF to the O-ring.
Inspection and Adjustment
INFOID:0000000009268033
INSPECTION AFTER INSTALLATION
Check for A/T fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Check the A/T fluid level. Refer to
1.
Output speed sensor
2.
O-ring
3.
Transaxle assembly
Front
JSDIA1935GB
DIFFERENTIAL SIDE OIL SEAL
TM-245
< REMOVAL AND INSTALLATION >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000009268034
Removal and Installation
INFOID:0000000009268035
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the front drive shafts from the transaxle assembly. Refer to
FAX-15, "Removal and Installation"
.
2. Remove the differential side oil seal using suitable tool.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mating surfaces
of the transaxle case and converter housing.
INSTALLATION
1. Drive the differential side oil seal into the transaxle case side (A)
and converter housing side (B) using suitable tool to the speci-
fied dimension.
CAUTION:
• Be careful not to scratch the lip of the differential side oil seal
when press-fitting it.
• Do not reuse differential side oil seal.
• Apply Genuine NISSAN Matic S ATF to the differential side oil
seal lip and around the oil seal.
2. Install the front drive shaft. Refer to
FAX-15, "Removal and Installation"
.
Inspection and Adjustment
INFOID:0000000009268036
INSPECTION AFTER INSTALLATION
Check for A/T fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
1.
Transaxle assembly
2.
Differential side oil seal (left side)
3.
Differential side oil seal (right side)
Front
Genuine NISSAN Matic S ATF
JSDIA1936ZZ
Dimension (C)
: 1.8
± 0.5 mm (0.071 ± 0.020 in).
Dimension (D)
: 1.8
± 0.5 mm (0.071 ± 0.020 in).
JSDIA1836ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст