Nissan Versa Sedan. Instruction — part 871
TM-390
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0967 PRESSURE CONTROL SOLENOID B
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of primary pressure solenoid valve. Replace transaxle assembly. Refer to
TM-452, "Removal and Installation"
CVT unit
Ground
Condition
Resistance
Terminal
3
Ground
CVT fluid temperature: 20
°C (68°F)
Approx. 5.3
Ω
CVT fluid temperature: 50
°C (122°F)
Approx. 6.0
Ω
CVT fluid temperature: 80
°C (176°F)
Approx. 6.7
Ω
P0998 SHIFT SOLENOID F
TM-391
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0998 SHIFT SOLENOID F
DTC Logic
INFOID:0000000009268203
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Shift the selector lever to “D” position and wait for 5 seconds or more.
3. Check the first trip DTC.
Is “P0998” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009268204
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK LOW BRAKE SOLENOID VALVE
Check low brake solenoid valve. Refer to
TM-391, "Component Inspection (Low Brake Solenoid Valve)"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Low Brake Solenoid Valve)
INFOID:0000000009268205
1.
CHECK LOW BRAKE SOLENOID VALVE
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0998
Shift solenoid F control circuit
low
The TCM low brake solenoid valve current
monitor reading is 200 mA or less continuous-
ly for 480 msec or more under the following di-
agnosis conditions:
• Diagnosis conditions
- Solenoid valve output current: 750 mA or
more
- GND short circuit diagnosis occurs in the
solenoid valve drive circuit.
- TCM power supply voltage: More than 11 V
• Harness or connector
(Low brake solenoid valve circuit short-
ed to ground)
• Low brake solenoid valve
TCM
Ground
Continuity
Connector
Terminal
F44
39
Ground
Not existed
TM-392
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P0998 SHIFT SOLENOID F
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of low brake solenoid valve. Replace transaxle assembly. Refer to
452, "Removal and Installation"
.
CVT unit
Ground
Condition
Resistance
Terminal
22
Ground
CVT fluid temperature: 20
°C (68°F)
Approx. 5.3
Ω
CVT fluid temperature: 50
°C (122°F)
Approx. 6.0
Ω
CVT fluid temperature: 80
°C (176°F)
Approx. 6.7
Ω
P0999 SHIFT SOLENOID F
TM-393
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0999 SHIFT SOLENOID F
DTC Logic
INFOID:0000000009268206
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Shift the selector lever to “D” position and wait for 5 seconds or more.
3. Check the first trip DTC.
Is “P0999” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009268207
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and CVT unit harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK LOW BRAKE SOLENOID VALVE
Check low brake solenoid valve. Refer to
TM-393, "Component Inspection (Low Brake Solenoid Valve)"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection (Low Brake Solenoid Valve)
INFOID:0000000009268208
1.
CHECK LOW BRAKE SOLENOID VALVE
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0999
Shift solenoid F control circuit
high
The TCM low brake solenoid valve current
monitor reading is 200 mA or less continuous-
ly for 200 msec or more under the following di-
agnosis conditions:
• Diagnosis conditions
- Solenoid valve output current: 750 mA or
more
- GND short diagnosis of the solenoid valve
circuit is not satisfied.
- TCM power supply voltage: More than 11 V
• Harness or connector
(Low brake solenoid valve circuit is
open or shorted to power supply)
• Low brake solenoid valve
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F44
39
F46
22
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст