Nissan Versa Sedan. Instruction — part 241
DLK-282
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT FENDER
A viscous urethane foam is installed on the back surface of front fender. When removing the front
fender, be careful to not deform the front fender while performing the procedure and removing the
viscous urethane foam a little at a time.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Adjust the following components as necessary.
- Hood assembly: Refer to
DLK-275, "HOOD ASSEMBLY : Adjustment"
.
- Front door assembly: Refer to
DLK-285, "DOOR ASSEMBLY : Adjustment"
.
• After adjusting, apply touch-up paint (body color) onto the head of the front fender bolts.
FENDER COVER
FENDER COVER : Removal and Installation
INFOID:0000000009268985
REMOVAL
1. Fully open hood assembly.
2. Disengage pawls beginning at the front of the fender cover and
working toward the rear of vehicle and then remove front fender
cover.
CAUTION:
When performing the procedure after removing fender
cover, protect the lower windshield glass with urethane etc.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• For installation, engage pawls to front fender and cowl top
cover in numerical order shown.
• Install so that there is no clearance between windshield and
cowl top cover.
JMKIA8031ZZ
JMKIA8032ZZ
FRONT DOOR
DLK-283
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR
Exploded View
INFOID:0000000009268986
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009268987
CAUTION:
• Use two people when removing or installing front door due to its heavy weight
• When removing and installing front door assembly, support the door using a suitable tool.
• Use shops cloths to protect surrounding components from damage during removal and installation
of front door assembly.
REMOVAL
1. Remove front door harness grommet (1) and then pull out the
harness from the vehicle (2).
1.
Front door assembly
2.
Grommet
3.
Striker bolt
4.
Door striker
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
9.
Grommet (Drive side only)
JMKIA8152GB
JMKIA8070ZZ
DLK-284
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR
2. Disconnect the harness connectors (A) from front door assem-
bly.
3. Remove door check link bolt (body side).
4. Remove door hinge nuts (door side) and front door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the hinge mating surface.
• After installation, check front door open/close, lock/unlock operation.
• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After installation, perform the front door adjustment procedure. Refer to
• After adjusting, apply touch-up paint (body color) onto the head of door hinge nuts.
JMKIA8071ZZ
FRONT DOOR
DLK-285
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY : Adjustment
INFOID:0000000009268988
Check the clearance and surface height between front door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
ADJUSTMENT PROCEDURE
1. Remove front fender. Refer to
DLK-281, "FRONT FENDER : Removal and Installation"
.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
Striker bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
JMKIA8146GB
Section
Measurement
Standard
A – A
Clearance
4.6
± 1.0 (0.18 ± 0.04)
Surface height
0.0
± 1.0 (0.0 ± 0.04)
B – B
Clearance
4.6
± 2.0 (0.18 ± 0.08)
Surface height
0.0
± 1.5 (0.0 ± 0.06)
C – C
Clearance
4.6
± 1.0 (0.18 ± 0.04)
Surface height
0.0
± 1.0 (0.0 ± 0.04)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст