Nissan Versa Sedan. Instruction — part 823
TM-198
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
P0973 SHIFT SOLENOID A
P0973 SHIFT SOLENOID A
DTC Logic
INFOID:0000000009267975
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Maintain the following conditions for 5 seconds or more.
3. Check the first trip DTC.
Is “P0973” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267976
1.
CHECK CIRCUIT BETWEEN TCM AND A/T UNIT
1. Turn the ignition switch OFF.
2. Disconnect the TCM connector and A/T unit connector.
3. Check the continuity between TCM harness connector and ground.
Is the check result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK SELECT SWITCH ON-OFF SOLENOID VALVE
Check the select switch ON-OFF solenoid valve. Refer to
TM-199, "Component Inspection (Select Switch ON-
.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0973
Shift Solenoid “A” Control Cir-
cuit Low
The following diagnosis condi-
tions are met, and the TCM se-
lect switch ON-OFF solenoid
valve monitor value is ON con-
tinuously for 0.5 seconds or
more.
• Diagnosis condition
- select switch ON-OFF sole-
noid valve: OFF
- TCM power supply voltage:
10 V < TCM power supply
voltage < 16 V
• Harness or connector
(Short circuit to ground in the
select switch ON-OFF sole-
noid valve circuit)
• Select switch ON-OFF sole-
noid valve
Selector lever
: N position
⇒ R position
TCM harness connector
Ground
Continuity
Connector
Terminal
F44
1
Ground
Does not exist
P0973 SHIFT SOLENOID A
TM-199
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning parts.
Component Inspection (Select Switch ON-OFF Solenoid Valve)
INFOID:0000000009267977
1.
CHECK SELECT SWITCH ON-OFF SOLENOID VALVE
Check the resistance between the A/T unit connector and ground.
Is the check result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of select switch ON-OFF solenoid valve. Replace the transaxle assembly.
TM-250, "Removal and Installation"
.
A/T unit connector
Ground
Condition
Resistance
Terminal
19
Ground
A/T fluid temperature: 20
°C
(68
°F)
Approx. 27
Ω
A/T fluid temperature: 50
°C
(122
°F)
Approx. 31
Ω
A/T fluid temperature: 80
°C
(176
°F)
Approx. 35
Ω
TM-200
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
P0974 SHIFT SOLENOID A
P0974 SHIFT SOLENOID A
DTC Logic
INFOID:0000000009267978
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Maintain the following conditions for 5 seconds or more.
3. Check the first trip DTC.
Is “P0974” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009267979
1.
CHECK CIRCUIT BETWEEN TCM AND A/T UNIT
1. Turn ignition switch OFF.
2. Disconnect the TCM connector and A/T unit connector.
3. Check the continuity between the TCM harness connector and the A/T unit harness connector.
Is the check result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK SELECT SWITCH ON-OFF SOLENOID VALVE
Check the select switch ON-OFF solenoid valve. Refer to
TM-201, "Component Inspection (Select Switch ON-
.
Is the check result normal?
YES >> Check
intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P0974
Shift Solenoid “A” Control Cir-
cuit High
The following diagnosis condi-
tions are met, and the TCM se-
lect switch ON-OFF solenoid
valve monitor value is OFF con-
tinuously for 0.5 seconds or
more.
• Diagnosis condition
- Select switch ON-OFF sole-
noid valve: ON
- TCM power supply voltage:
10 V < TCM power supply
voltage < 16 V
• Harness or connector
(Select switch ON-OFF sole-
noid valve circuit is open or
shorted to power supply)
• Select switch ON-OFF sole-
noid valve
Selector lever
: N position
⇒ R position
TCM harness connector
A/T unit harness connector
Continuity
Connector
Terminal
Connector
Terminal
F44
1
F46
19
Exists
P0974 SHIFT SOLENOID A
TM-201
< DTC/CIRCUIT DIAGNOSIS >
[4AT: RE4F03C]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NO
>> Repair or replace the malfunctioning parts.
Component Inspection (Select Switch ON-OFF Solenoid Valve)
INFOID:0000000009267980
1.
CHECK SELECT SWITCH ON-OFF SOLENOID VALVE
Check the resistance between the A/T unit connector and ground.
Is the check result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of select switch ON-OFF solenoid valve. Replace the transaxle assembly.
TM-250, "Removal and Installation"
.
A/T unit connector
Ground
Condition
Resistance
Terminal
19
Ground
A/T fluid temperature: 20
°C
(68
°F)
Approx. 27
Ω
A/T fluid temperature: 50
°C
(122
°F)
Approx. 31
Ω
A/T fluid temperature: 80
°C
(176
°F)
Approx. 35
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст