Nissan Versa Sedan. Instruction — part 65
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
BRAKE SW 1 [On/Off]
×
Indicates condition of brake switch.
BRAKE SW 2 [On/Off]
Indicates condition of brake switch.
DETE/CANCL SW [On/Off]
×
Indicates condition of P (park) position.
SFT PN/N SW [On/Off]
×
Indicates condition of P (park) or N (neutral) position.
PUSH SW -IPDM [On/Off]
Indicates condition of push-button ignition switch received from IPDM E/R on
CAN communication line.
IGN RLY1 -F/B [On/Off]
Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line.
DETE SW -IPDM [On/Off]
Indicates condition of detent switch received from TCM on CAN communication
line.
SFT PN -IPDM [On/Off]
Indicates condition of P (park) or N (neutral) position from TCM on CAN com-
munication line.
SFT P -MET [On/Off]
Indicates condition of P (park) position from TCM on CAN communication line.
SFT N -MET [On/Off]
Indicates condition of N (neutral) position from IPDM E/R on CAN communica-
tion line.
ENGINE STATE [Stop/Start/Crank/Run]
×
Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h]
×
Indicates condition of vehicle speed signal received from ABS on CAN commu-
nication line.
VEH SPEED 2 [mph/km/h]
×
Indicates condition of vehicle speed signal received from combination meter on
CAN communication line.
DOOR STAT -DR [LOCK/READY/UNLK]
×
Indicates condition of driver side door status.
DOOR STAT -AS [LOCK/READY/UNLK]
×
Indicates condition of passenger side door status.
ID OK FLAG [Set/Reset]
Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset]
Indicates condition of engine start possibility.
PRMT RKE STRT [Set/Reset]
Indicates condition of engine start possibility from Intelligent Key.
RKE OPE COUN1 [0-19]
×
When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19]
×
When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.
TRNK/HAT MNTR [On/Off]
Indicates condition of trunk room lamp switch.
RKE-LOCK [On/Off]
Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]
Indicates condition of unlock signal from Intelligent Key.
RKE-TR/BD [On/Off]
Indicates condition of trunk open signal from Intelligent Key.
RKE-PANIC [On/Off]
Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off]
Indicates condition of mode change signal from Intelligent Key.
Monitor Item [Unit]
Main
Description
Test Item
Description
INSIDE BUZZER
This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
LCD
This test is able to check combination meter display information [Off/LK WN/OUTKEY/NO
KY/BATT/INSRT/SFT P/ROTAT/ID NG/B&P I/B&P N].
BATTERY SAVER
This test is able to check battery saver operation [On/Off].
ENGINE SW ILLUMI
This test is able to check push-button ignition switch START indicator operation [On/Off].
PUSH SWITCH INDICATOR
This test is able to check push-button ignition switch indicator operation [On/Off].
TRUNK/BACK DOOR
This test is able to check trunk actuator operation [Open].
INT LAMP
This test is able to check interior room lamp operation [On/Off].
INDICATOR
This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
BCS-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
FLASHER
This test is able to check hazard lamp operation [LH/RH/Off].
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation [On/Off].
HORN
This test is able to check horn operation [On].
P RANGE
This test is able to check CVT shift selector illumination operation [On/Off].
Test Item
Description
Support Item
Setting
Description
LOCK/UNLOCK BY I-KEY
On*
Door lock/unlock function from Intelligent Key ON.
Off
Door lock/unlock function from Intelligent Key OFF.
TRUNK/GLASS HATCH OPEN
On*
Buzzer reminder function from trunk opener switch.
Off
No buzzer reminder function from trunk opener switch.
ANTI KEY LOCK IN FUNCTI
On*
Anti lock out setting ON.
Off
Anti lock out setting OFF.
ANS BACK I-KEY UNLOCK
Off
No buzzer reminder when doors are unlocked with request switch.
On*
Buzzer reminder when doors are unlocked with request switch.
ANS BACK I-KEY LOCK
Horn Chirp
Horn chirp reminder when doors are locked with request switch.
Buzzer*
Buzzer reminder when doors are locked with request switch.
Off
No reminder when doors are locked with request switch.
HORN WITH KEYLESS LOCK
Off
Horn chirp reminder when doors are locked with Intelligent Key.
On*
No horn chirp reminder when doors are locked with Intelligent Key.
ENGINE START BY I-KEY
On*
Engine start function from Intelligent Key ON.
Off
Engine start function from Intelligent Key OFF.
HAZARD ANSWER BACK
Lock/Unlock*
Hazard warning lamp activation when doors are locked/unlocked
with Intelligent Key or request switch.
Unlock Only
Hazard warning lamp activation when doors are unlocked with Intel-
ligent Key or request switch.
Lock Only
Hazard warning lamp activation when doors are locked with Intelli-
gent Key or request switch.
Off
No hazard warning lamp activation when doors are locked/unlocked
with Intelligent Key or request switch.
INSIDE ANT DIAGNOSIS
—
This function allows inside key antenna self-diagnosis.
CONFIRM KEY FOB ID
—
Intelligent Key ID code can be checked.
SHORT CRANKING OUTPUT
Start
70 msec
Starter motor operation duration time setting.
100 msec
200 msec
End
—
PANIC ALARM SET
MODE 3
1.5 sec
Intelligent Key panic alarm button setting.
MODE 2
OFF
MODE 1*
0.5 sec
LO- BATT OF KEY FOB WARN
On*
Intelligent Key low battery warning ON.
Off
Intelligent Key low battery warning OFF.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: Initial Setting
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000009268623
DATA MONITOR
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000009268624
ECU IDENTIFICATION
The BCM part number is displayed.
SELF DIAGNOSTIC RESULT
WORK SUPPORT
CONFIGURATION
BCS-57, "CONFIGURATION (BCM) : Description"
.
AUTO LOCK SET
MODE7
5 min
Auto door lock time setting.
MODE6
4 min
MODE5
3 min
MODE4
2 min
MODE3*
1 min
MODE2
30 sec
MODE1
Off
TRUNK OPEN DELAY
MODE 3
1.5 sec
Intelligent Key trunk open button setting.
MODE 2
OFF
MODE 1*
0.5 sec
Support Item
Setting
Description
Monitor Item [Unit]
Description
FR WIPER HI [On/Off]
Indicates condition of wiper operation of combination switch.
FR WIPER LOW [On/Off]
FR WASHER SW [On/Off]
FR WIPER INT [On/Off]
INT VOLUME [1 - 7]
Indicates condition of intermittent wiper operation of combination switch.
TURN SIGNAL R [On/Off]
Indicates condition of right turn signal operation of combination switch.
TURN SIGNAL L [On/Off]
Indicates condition of left turn signal operation of combination switch.
TAIL LAMP SW [On/Off]
Indicates condition of tail lamp switch operation of combination switch.
HI BEAM SW [On/Off]
Indicates condition of Hi beam switch operation of combination switch.
HEAD LAMP SW 1 [On/Off]
Indicates condition of head lamp switch 1 operation of combination switch.
HEAD LAMP SW 2 [On/Off]
Indicates condition of head lamp switch 2 operation of combination switch.
PASSING SW [On/Off]
Indicates condition of passing switch operation of combination switch.
FR FOG SW [On/Off]
Indicates condition of front fog lamp switch operation of combination switch.
Support Item
Setting
Description
RESET SETTING VALUE
Reset
Returns BCM to initial value in factory shipment.
Cancel
Cancels the reset function.
BCS-24
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
CAN DIAG SUPPORT MNTR
LAN-12, "CAN Diagnostic Support Monitor"
.
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000009268625
SELF DIAGNOSTIC RESULT
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000009268626
DATA MONITOR
Monitor Item [Unit]
Description
CONFRM ID ALL [Yet/DONE]
Switches to DONE when an Intelligent Key is registered.
CONFIRM ID4 [Yet/DONE]
CONFIRM ID3 [Yet/DONE]
CONFIRM ID2 [Yet/DONE]
CONFIRM ID1 [Yet/DONE]
TP 4 [Yet/DONE]
DONE indicates the number of Intelligent Key ID which has been registered.
TP 3 [Yet/DONE]
TP 2 [Yet/DONE]
TP 1 [Yet/DONE]
PUSH SW [On/Off]
Indicates condition of push-button ignition switch.
Test Item
Description
THEFT IND
This test is able to check security indicator operation [On/Off].
Support Item
Setting
Description
CONFIRM DONGLE ID
—
Dongle ID code can be read.
Monitor Item [Unit]
Description
REQ SW -DR [On/Off]
Indicates condition of door request switch LH.
REQ SW -AS [On/Off]
Indicates condition of door request switch RH.
PUSH SW [On/Off]
Indicates condition push-button ignition switch.
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH.
DOOR SW-RR [On/Off]
Indicates condition of rear door switch RH.
DOOR SW-RL [On/Off]
Indicates condition of rear door switch LH.
DOOR SW-BK [On/Off]
Indicates condition of trunk switch.
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW [On/Off]
Indicates condition of unlock signal from door lock and unlock switch.
KEY CYL LK-SW [On/Off]
Indicates condition of lock signal from door key cylinder switch.
KEY CYL UN-SW [On/Off]
Indicates condition of unlock signal from door key cylinder switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст