Nissan Versa Sedan. Instruction — part 373
INTAKE MANIFOLD
EM-27
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INTAKE MANIFOLD
Exploded View
INFOID:0000000009266647
Removal and Installation
INFOID:0000000009266648
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove air duct (inlet), air duct and air cleaner assembly. Refer to
EM-25, "Removal and Installation"
2. Disconnect water hoses from electric throttle control actuator.
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on drive belt.
3. Remove electric throttle control actuator.
CAUTION:
• Handle carefully to avoid any shock to electric throttle control actuator.
• Do not disassemble electric throttle control actuator.
4. Disconnect harness connector and vacuum hose from EVAP purge control solenoid valve.
CAUTION:
Handle EVAP canister purge volume control solenoid valve carefully and avoid impacts.
5. Disconnect vacuum hose for brake booster from intake manifold.
1.
EVAP canister purge volume control
solenoid valve
2.
Hose clamp
3.
Vacuum hose
4.
PCV hose
5.
Hose clamp
6.
Intake manifold support
7.
Gasket
8.
Intake manifold
9.
Electric throttle control actuator
10. Gasket
11. EVAP service port
A.
To air duct
B.
To centralized under-floor piping
C.
To brake booster
D.
To air duct
E.
To rocker cover
AWBIA1471ZZ
EM-28
< REMOVAL AND INSTALLATION >
[HR16DE]
INTAKE MANIFOLD
6. Remove intake manifold bolts at the rocker cover.
7. Loosen bolts in reverse order as shown.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
8. Remove intake manifold.
9. Remove EVAP purge control solenoid valve from intake manifold if necessary.
CAUTION:
Handle EVAP canister purge volume control solenoid valve carefully and avoid impacts.
10. Remove intake manifold support (1) if necessary.
CAUTION:
The intake manifold support functions as a guide for install-
ing the intake manifold.
INSTALLATION
Installation is in the reverse order of removal.
Intake Manifold
1. Install the new gasket to the intake manifold.
• Align the protrusions used for checking gasket installation con-
dition with the clearance grooves (A) of the intake manifold
groove.
CAUTION:
Do not reuse the gasket.
NOTE:
New gasket for electronically-controlled throttle can be installed
when the electronically-controlled throttle is installed.
2. Place the intake manifold into position.
CAUTION:
AWBIA1128GB
JSBIA1219ZZ
JPBIA4741ZZ
JSBIA1220ZZ
INTAKE MANIFOLD
EM-29
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Check that the oil level gauge guide is not detached from the securing clip of the water inlet due to
interference of intake manifold.
3. Tighten the bolts to specification in the numerical order as
shown.
4. Tighten the intake manifold bolts to specification at the rocker
cover.
Electric Throttle Control Actuator
• Tighten bolts of electric throttle control actuator equally and diagonally in several steps.
• Perform “Throttle Valve Closed Position Learning” after repair when removing harness connector of the elec-
tric throttle control actuator. Refer to
.
• Perform “Throttle Valve Closed Position Learning” and “Idle Air Volume Learning” after repair when replacing
electric throttle control actuator. Refer to
JSBIA1219ZZ
AWBIA1128GB
EM-30
< REMOVAL AND INSTALLATION >
[HR16DE]
EXHAUST MANIFOLD
EXHAUST MANIFOLD
Exploded View
INFOID:0000000009266649
Removal and Installation
INFOID:0000000009266650
REMOVAL
1. Remove air duct (inlet), air duct and air cleaner assembly. Refer to
2. Remove exhaust center tube and front tube. Refer to
.
3. Remove the air-fuel ratio sensor harness bracket from the cylinder head on the right rear side.
4. Remove exhaust manifold cover.
5. Disconnect the harness from air-fuel ratio sensor 1.
6. Remove exhaust manifold side bolt of exhaust manifold stay.
7. Remove exhaust manifold.
AWBIA1472ZZ
1.
Exhaust manifold cover
2.
Harness bracket
3.
Air-fuel ratio sensor 1
4.
Exhaust manifold stay
5.
Heat insulator
6.
Exhaust manifold
7.
Exhaust manifold cover
8.
Gasket
: Engine front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст