Nissan Versa Sedan. Instruction — part 372
DRIVE BELT IDLER PULLEY
EM-23
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
DRIVE BELT IDLER PULLEY
Exploded View
INFOID:0000000009266643
Removal and Installation
INFOID:0000000009266644
REMOVAL
1. Remove the fender protector (RH). Refer to
EXT-26, "Removal and Installation"
.
2. Remove the air duct inlet assembly. Refer to
EM-25, "Removal and Installation"
3. Remove drive belt. Refer to
EM-16, "Removal and Installation"
.
4. Remove the lock nut, and then remove the plate, idler pulley, and washer.
5. Remove the center shaft together with the spacer and the adjusting bolt.
INSTALLATION
1.
Generator bracket
2.
Center shaft
3.
Spacer
4.
Adjusting bolt
5.
Washer
6.
Idler pulley
7.
Plate
AWBIA1470ZZ
EM-24
< REMOVAL AND INSTALLATION >
[HR16DE]
DRIVE BELT IDLER PULLEY
1. Insert the center shaft (1) into the slide groove of the spacer (2).
Fully screw in the adjusting bolt (3) in the belt loosening direc-
tion (
).
• At that time, place the flange (a) of the adjusting bolt and the
seat (b) of the center shaft on the spacer.
2. Place each surface (c and d) of the spacer on the generator
bracket. Install the washer, idler pulley, and plate, and then tem-
porarily tighten the lock nut.
3. Installation is in the reverse order of removal.
Lock nut
(Temporary tightening)
: 4.4 N·m (0.45 kg-m, 39 in-lb)
PBIC3885E
AIR CLEANER AND AIR DUCT
EM-25
< REMOVAL AND INSTALLATION >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000009266645
Removal and Installation
INFOID:0000000009266646
REMOVAL
NOTE:
Mass air flow sensor is removable as an assembly with the air cleaner cover.
1. Remove air duct (inlet) from the air cleaner body.
2. Disconnect PCV hose from the air duct.
3. Remove the air duct (between air cleaner case and electric throttle control actuator).
• Add matching marks if necessary for easier installation.
4. Remove air cleaner assembly with the following steps:
a. Disconnect the harness connector from mass air flow sensor.
b. Remove the two air cleaner body bolts.
c. Pull up on the air cleaner assembly to disengage it from the grommet and remove the air cleaner assem-
bly.
CAUTION:
• Do not shock the mass air flow sensor.
• Do not disassemble the mass air flow sensor.
• Do not touch the sensor of the mass air flow sensor.
INSPECTION AFTER REMOVAL
Inspect air duct (inlet) and air duct for cracks, tears, or breaks.
1.
Clamp
2.
PCV hose
3.
Clamp
4.
Mount rubber
5.
Air duct (inlet)
6.
Air cleaner body
7.
Grommet
8.
Air cleaner filter
9.
Air cleaner cover
10. Mass air flow sensor
11. Air duct
12. Clamp
A.
To electric throttle control actuator
B.
To rocker cover
AWBIA1126ZZ
EM-26
< REMOVAL AND INSTALLATION >
[HR16DE]
AIR CLEANER AND AIR DUCT
Replace air duct (inlet) and air duct if any problems are found.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Align marks, attach each joint and screw clamps firmly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст