Nissan Versa Sedan. Instruction — part 678
SE-38
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
PASSENGER SIDE : Exploded View
INFOID:0000000009268533
WITH REMOVABLE HEADREST
ALJIA1000ZZ
1.
Seatback trim
2.
Seatback pad
3.
Headrest
4.
Headrest holder (free)
5.
Headrest holder (locked)
6.
Chute rod
7.
Seat frame assembly
8.
Side air bag module
9.
Recline lever
FRONT SEAT
SE-39
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
WITHOUT REMOVABLE HEADREST
10. Seat cushion outer finisher (RH)
11. Seat cushion trim
12. Seat cushion pad
13. Seat belt buckle
14. Seat cushion outer finisher (LH)
ALJIA0999ZZ
1.
Seatback trim
2.
Seatback pad
3.
Chute rod
4.
Side air bag module
5.
Recline lever
6.
Seat cushion outer finisher (RH)
SE-40
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
PASSENGER SIDE : Disassembly and Assembly
INFOID:0000000009268534
SEATBACK ASSEMBLY
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,
do not let it hang by the wire harness.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• Replace the side air bag module if it has been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
• Do not attempt to disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93
°C (200°F).
• Do not expose the side air bag module to any oil, grease, detergent or water.
• During disassembly, do not damage the seatback board, chutes, connectors, retainers, clips, module
harness or the side air bag module.
NOTE:
If the vehicle has been involved in a collision and the side air bag module has deployed, the front seatback
assembly must be replaced.
Disassembly
1. Remove the front seat assembly. Refer to
SE-20, "PASSENGER SIDE : Removal and Installation"
2. Release the lower seatback trim retainer strap (A) from the
cushion springs.
3. Release the J-hook retainer (C), unzip seatback zipper (A) and
release J-clips (B) holding the seatback trim to the seat frame
assembly.
7.
Seat cushion trim
8.
Seat cushion pad
9.
Seat belt buckle
10. Seat cushion outer finisher (LH)
11. Seat frame assembly
AWJIA0913ZZ
AWJIA0914ZZ
FRONT SEAT
SE-41
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4. Reach up through the seatback trim and release locks as shown
and remove the headrest holders (if equipped).
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left)
5. Remove and discard the two chute rod nuts (A), then route the
chute rod (1) through the opening and remove it from the chute
(B).
CAUTION:
Do not reuse the chute rod nuts.
6. Release the side air bag module harness from the seat frame
assembly.
NOTE:
Take note of harness routing and attachment location for accu-
rate installation.
a. From the back of the seat unclip the side air bag module har-
ness clips (
).
7. Remove and discard the two side air bag module nuts (A).
CAUTION:
Do not reuse the side air bag module nuts.
8. Disengage the side air bag module studs from the seatback frame and lift the seatback trim and seatback
pad as an assembly from the seat frame assembly.
PIIB4084J
AWJIA0922ZZ
AWJIA0915ZZ
AWJIA0916ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст