Nissan Versa Sedan. Instruction — part 247
DLK-306
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing door key cylinder rod on the LH front door, be sure to rotate door key cylinder rod
holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
REAR DOOR LOCK
DLK-307
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000009269014
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009269015
REMOVAL
1. Remove inside handle. Refer to
DLK-308, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-309, "OUTSIDE HANDLE : Removal and Installation"
.
3. Remove bolt (A) from the front door glass channel rear (1).
4. Disconnect the harness connector from door lock actuator.
5. Remove door lock assembly bolts and door lock assembly.
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
Bolt
5.
Door lock assembly
6.
Inside handle
7.
Outside handle
8.
Front gasket
9.
Clip
Pawl
Front
JMKIA8161GB
JMKIA8086ZZ
DLK-308
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolt. Always replace it with a new one when it is removed.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Apply a suit-
able multi-purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009269016
REMOVAL
1. Remove rear door finisher. Refer to
INT-17, "Removal and Installation"
.
2. Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
3. Disengage lock knob cable (2) and inside handle cable (3) from
cable clip (1).
4. Remove inside handle bolt.
5. Disengage inside handle (1) from door panel (2) by sliding
toward vehicle rear and then separating.
: Pawl
: Front
JMKIA8087ZZ
JMKIA5704ZZ
JMKIA8079ZZ
REAR DOOR LOCK
DLK-309
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6. Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009269017
REMOVAL
1. Fully close rear door glass.
2. Remove rear door finisher. Refer to
INT-17, "Removal and Installation"
.
3. Remove sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
4. Remove door side grommet, and loosen bolt from grommet
hole.
5. While pulling outside handle, remove outside handle escutch-
eon.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст