Nissan Versa Sedan. Instruction — part 248
DLK-310
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
6. Pull outside handle (1) rearward and outward to remove.
7. Remove front gasket (1) and rear gasket (2).
: Front
8. Slide outside handle bracket toward rear of vehicle to remove.
: Front
9. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA0524ZZ
JMKIA5889ZZ
JMKIA5890ZZ
JMKIA5891ZZ
TRUNK LID LOCK
DLK-311
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID LOCK
Exploded View
INFOID:0000000009269018
TRUNK LID LOCK
TRUNK LID LOCK : Removal and Installation
INFOID:0000000009269019
REMOVAL
1. Remove trunk lid finisher (If equipped). Refer to
INT-35, "Removal and Installation"
2. Disengage rod holder (1) by lifting upward, and then separate
trunk lid lock rod (3) from trunk lid lock assembly (2).
3. Remove trunk lid lock assembly bolts.
1.
Trunk lid opener handle
2.
Trunk lid opener cable
3.
Cable protector
4.
Trunk lid striker
5.
Trunk lid lock assembly
6.
Key rod
7.
Trunk key cylinder
JMKIA8173GB
JMKIA8131ZZ
DLK-312
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
TRUNK LID LOCK
4. Disconnect the harness connector and then remove trunk lid
lock assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check trunk lid open/close, lock/unlock operation.
• Check trunk lid lock assembly for poor lubrication. Apply a
suitable multi-purpose grease to trunk lid lock if necessary.
TRUNK LID OPENER HANDLE
TRUNK LID OPENER HANDLE : Removal and Installation
INFOID:0000000009269020
REMOVAL
1. Remove front kicking plate (LH). Refer to
INT-20, "KICKING PLATE INNER : Removal and Installation"
.
2. Release pawl using a suitable tool (A) and open the harness
clip.
: Pawl
3. Position floor carpet aside as necessary to access the trunk lid opener handle bolts.
4. Remove the trunk lid opener handle bolts.
5. Remove trunk lid opener cable from trunk lid opener handle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check trunk lid open/close, lock/unlock operation.
• After installation, perform the trunk lid adjustment procedure. Refer to
.
TRUNK LID OPENER CABLE
JMKIA8132ZZ
JMKIA8133ZZ
AWJIA0737ZZ
TRUNK LID LOCK
DLK-313
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID OPENER CABLE : Removal and Installation
INFOID:0000000009269021
REMOVAL
1. Remove trunk lid striker. Refer to
DLK-295, "TRUNK LID STRIKER : Removal and Installation"
2. Remove trunk side finisher (LH). Refer to
INT-33, "TRUNK SIDE FINISHER : Removal and Installation"
.
3. Remove rear seat cushion. Refer to
SE-23, "Removal and Installation - Seat Cushion Assembly"
4. Remove center pillar lower finisher (LH). Refer to
INT-23, "CENTER PILLAR LOWER FINISHER :
.
5. Remove trunk lid opener handle. Refer to
DLK-312, "TRUNK LID OPENER HANDLE : Removal and
.
6. Release pawl using a suitable tool (A) and open the harness
clip.
: Pawl
7. Remove trunk lid opener cable.
CAUTION:
Use care not to damage the trunk lid opener cable when removing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform the trunk lid adjustment procedure. Refer to
EMERGENCY LEVER
EMERGENCY LEVER : Removal and Installation
INFOID:0000000009269022
Removal
1. Release the pawls using a suitable tool and remove emergency
release handle (1) from trunk lid assembly.
: Pawl
2. Disconnect emergency release handle cable (2) from trunk lid
lock assembly (3).
AWJIA0737ZZ
ALKIA2310ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст