Nissan Versa Sedan. Instruction — part 886
TM-450
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
FLUID COOLER HOSE
FLUID COOLER HOSE
Exploded View
INFOID:0000000009315566
Removal and Installation
INFOID:0000000009315567
Inspection and Adjustment
INFOID:0000000009315568
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
PLUG
TM-451
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PLUG
Description
INFOID:0000000009268276
Replace the O-ring if oil leakage or exudes from the plug.
Exploded View
INFOID:0000000009268277
Removal and Installation
INFOID:0000000009268278
REMOVAL
Remove the plugs and O-rings.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Apply Genuine NISSAN CVT Fluid NS-3 to O-rings.
Inspection and Adjustment
INFOID:0000000009268279
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
1.
Plug
2.
O-ring
3.
O-ring
4.
Plug
Genuine NISSAN CVT Fluid NS-3
JSDIA1889GB
TM-452
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
TRANSMISSION ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Exploded View
INFOID:0000000009268280
Removal and Installation
INFOID:0000000009268281
WARNING:
• Do not open the radiator cap or drain plug when the engine is hot. Hot liquid may spray out, causing
serious injury.
• Perform these steps after the coolant temperature has cooled sufficiently.
NOTE:
• When replacing the TCM and transaxle assembly as a set, replace the transaxle assembly first and then
replace the TCM. Refer to
.
• When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from
spilling.
REMOVAL
1. Remove the battery. Refer to
PG-63, "Removal and Installation"
TM-437, "Removal and Installation"
3. Remove the battery plate.
4. Remove the air duct and air cleaner case. Refer to
EM-25, "Removal and Installation"
.
5. Disconnect the harness connectors from the following components and remove the harness from the tran-
saxle.
1.
Transaxle assembly
A : For the tightening torque, refer to
TM-452, "Removal and Installation"
JSDIA1890ZZ
TRANSMISSION ASSEMBLY
TM-453
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• CVT unit. Refer to
TM-258, "Removal and Installation Procedure for CVT Unit Connector"
• Transmission range switch
• Primary speed sensor
• Secondary speed sensor
• Output speed sensor
• Crankshaft position sensor. Refer to
.
• Ground
6. Disconnect the control cable from the transaxle assembly. Refer to
.
7. Disconnect the CVT water hose A and water hose C from engine side.
TM-447, "Removal and Installa-
8. Disconnect the heater hose from the water bypass pipe.
9. Remove the left and right drive shafts. Refer to
FAX-15, "Removal and Installation"
.
10. Remove the drive shaft heat insulator.
11. Remove starter motor. Refer to
STR-31, "Removal and Installation"
.
12. Remove the right and left fender protectors. Refer to
EXT-26, "Removal and Installation"
.
13. Rotate the crankshaft and remove the nuts that secure the drive plate to the torque converter.
CAUTION:
Rotate crankshaft clockwise (as viewed from the front of the engine).
14. Remove the rear torque rod. Refer to
.
15. Set a transmission jack under the transaxle assembly.
CAUTION:
Be careful not to contact the drain plug when setting the transmission jack.
16. Set a transmission jack under the engine assembly.
CAUTION:
Be careful not to contact the drain plug when setting the transmission jack.
17. Remove the left engine mounting insulator. Refer to
18. Remove the left engine mounting bracket (LH). Refer to
19. Remove the bolts that fasten the transaxle assembly and engine assembly.
20. Remove the transaxle assembly from the vehicle.
CAUTION:
Do not drop the torque converter.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-rings.
• When installing the transaxle assembly onto the engine assembly,
check the engagement of the dowel pins (
).
JSDIA1184ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст