Nissan Versa Sedan. Instruction — part 569
MA-34
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
ROAD WHEEL : Tire Rotation
INFOID:0000000009269073
• Follow the maintenance schedule for tire rotation service intervals.
MA-6, "Explanation of General Maintenance"
• When installing the wheel, tighten wheel nuts to the specified
torque.
CAUTION:
• Do not include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
• Use NISSAN genuine wheel nuts for aluminum wheels.
• Perform the ID registration, after tire rotation. Refer to
BRAKE FLUID LEVEL AND LEAKS
BRAKE FLUID LEVEL AND LEAKS : Inspection
INFOID:0000000009269074
BRAKE FLUID LEVEL
• Check that the fluid level in the reservoir tank is within the specified
range between the MAX – MIN lines as shown.
• Visually check for any brake fluid leakage around the reservoir
tank.
• Check the brake system for any leakage if the fluid level is
extremely low (lower than MIN).
• Check the brake system for fluid leakage if the warning lamp
remains illuminated even after the parking brake is released.
• Check the reservoir tank for foreign matter (e.g., dust) and oils
other than brake fluid.
BRAKE LINES AND CABLES
BRAKE LINES AND CABLES : Inspection
INFOID:0000000009269075
BRAKE LINES
1. Check brake lines (pipes and hoses) for cracks, deterioration or
other damage. Replace any damaged parts.
2. Check for brake fluid leaks by fully depressing brake pedal while
engine is running.
CAUTION:
Retighten the applicable connection to the specified torque
and repair any abnormal (damaged, worn or deformed) part
if any brake fluid leaks are present.
PARKING BRAKE CABLES
Wheel balance
Dynamic (At flange)
Static (At flange)
Maximum allowable im-
balance
Refer to
.
SMA829C
Wheel nut tightening torque
: 113 N·m (12 kg-m, 83 ft-lb)
JPFIA0007ZZ
SBR389C
CHASSIS AND BODY MAINTENANCE
MA-35
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Check parking brake cables for improper attachment, leaks, chafing, abrasions, deterioration, etc.
BRAKE FLUID
BRAKE FLUID : Draining
INFOID:0000000009269076
CAUTION:
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe
it off immediately and wash with water if it gets on a painted surface.
• Turn the ignition switch OFF and disconnect battery negative terminal before performing work.
1. Connect a vinyl tube to the bleed valve.
2. Depress the brake pedal and loosen the bleeder valve to gradu-
ally discharge brake fluid.
BRAKE FLUID : Refilling
INFOID:0000000009269077
CAUTION:
• Turn the ignition switch OFF and disconnect battery negative terminal before performing work.
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe
it off immediately and wash with water if it gets on a painted surface.
1. Check that there is no foreign material in the reservoir tank, and
refill with new brake fluid.
CAUTION:
• Do not reuse drained brake fluid.
• Do not allow foreign matter (e.g., dust) and oils other than
brake fluid to enter the reservoir tank.
2. Loosen the bleeder valve, slowly depress the brake pedal to the
full stroke, and then release the pedal. Repeat this operation at
intervals of 2 or 3 seconds until new brake fluid is discharged.
Then close the bleeder valve with the brake pedal depressed.
Repeat the same work on each wheel.
3. Perform the air bleeding. Refer to
BRAKE FLUID : Bleeding Brake System
INFOID:0000000009269078
CAUTION:
• Turn the ignition switch OFF and disconnect battery negative terminal before performing the work.
• Monitor the fluid level in the reservoir tank while performing the air bleeding
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe
it off immediately and wash with water if it gets on a painted surface.
• Always use new brake fluid for refilling. Do not reuse the drained brake fluid.
• Do not allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.
1. Connect a vinyl tube to the bleeder valve of the rear right brake.
2. Fully depress the brake pedal 4 to 5 times.
3. Loosen the bleeder valve and bleed air with the brake pedal depressed, and then quickly tighten the
bleeder valve.
4. Repeat steps 2 and 3 until all of the air is out of the brake line.
5. Tighten the bleeder valve to the specified torque.
• Front disc brake: refer to
BR-36, "BRAKE CALIPER ASSEMBLY : Exploded View"
• Rear drum brake: refer to
.
BRA0007D
PFIA0403J
MA-36
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
6. Perform steps 1 to 5. Occasionally fill with the brake fluid in order to keep the reservoir tank at least half of
MAX line. Bleed air in the following order: rear right brake
→ front left brake → rear left brake → and front
right brake in order.
7. Check that the fluid level in the reservoir tank is within the specified range after air bleeding. Refer to
8. Check each item of brake pedal. Adjust it if the measurement value is not the standard. Refer to
.
DISC BRAKE
DISC BRAKE : Inspection
INFOID:0000000009269079
BRAKE PAD
Check the brake pads and components for any excessive wear or
damage. Repair or replace any component as necessary.
DISC ROTOR
Check the condition of the disc rotor for any excessive wear or dam-
age. Repair or replace any component as necessary.
CALIPER
Check the caliper and hose fittings for any leaks or damage. Repair
or replace any component as necessary.
DRUM BRAKE
DRUM BRAKE : Inspection
INFOID:0000000009269080
BRAKE LINING
Brake pad specifications
: Refer to
.
BRA0010D
Disc rotor specifications
: Refer to
.
SMA260A
SMA922A
CHASSIS AND BODY MAINTENANCE
MA-37
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Check the lining thickness (A).
• Check the lining for excessive wear, damage, and peeling.
• Repair or replace any components as necessary.
BRAKE DRUM
• Check the inner diameter of brake drum.
• Shoe sliding surface for excessive wear and damage.
• Check the inside of the drum for excessive wear, damage, and
cracks.
NOTE:
Measurement area is the lining contact surface (center).
• Repair or replace any components as necessary.
WHEEL CYLINDER
• Check the wheel cylinder for brake fluid leakage.
• Check for wear, damage, and looseness.
• Check the return spring for settling.
• Check the back plate for damage, cracks, and deformation.
• Repair or replace any components as necessary.
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000009269081
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
AXLE AND SUSPENSION PARTS
Brake lining specifications
: Refer to
SBR021A
Brake lining specifications
: Refer to
SBR022A
WFIA0528E
JPPIA0013GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст