Nissan Versa Sedan. Instruction — part 741
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
SRC-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> Clear DTC. Inspection End.
6.
SEAT BELT PRE-TENSIONER LH
1. Replace the seat belt pre-tensioner LH. Refer to
SR-29, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
RELATED HARNESS
Replace the related harness.
>> END
SRC-60
< DTC/CIRCUIT DIAGNOSIS >
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
Description
INFOID:0000000009269160
DTC B1081 – B1084 SEAT BELT PRE-TENSIONER RH
The seat belt pre-tensioner RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner RH.
PART LOCATION
SRC-4, "Component Parts Location"
.
DTC Logic
INFOID:0000000009269161
DTC DETECTION LOGIC
With CONSULT
Without CONSULT
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check for DTC using CONSULT.
Is the DTC detected?
YES (Current DTC)>>Refer to
YES (Past DTC)>>GO TO 2.
NO
>> Inspection End.
2.
ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased?
YES
>> Inspection End.
NO
>> Refer to
DTC CONFIRMATION PROCEDURE (Without CONSULT)
CONSULT name
DTC
DTC detecting condition
Repair order
PRE-TEN FRONT RH
[OPEN]
B1081
RH seat belt pre-tensioner circuit is open.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the front RH seat belt pre-tensioner.
4.
Replace the air bag diagnosis sensor unit.
5.
Replace the related harness.
PRE-TEN FRONT RH
[VB-SHORT]
B1082
RH seat belt pre-tensioner circuit is short-
ed to a power supply circuit.
PRE-TEN FRONT RH
[GND-SHORT]
B1083
RH seat belt pre-tensioner circuit is short-
ed to ground.
PRE-TEN FRONT RH
[SHORT]
B1084
RH seat belt pre-tensioner circuits are
shorted to each other.
WHIA0262E
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
SRC-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-15, "Trouble Diagnosis without CONSULT"
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009269162
1.
HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis unit to the end component (including
any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-45, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage
NOTE
.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 5.
NO
>> Refer to
GI-45, "Intermittent Incident"
.
5.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
SRC-62
< DTC/CIRCUIT DIAGNOSIS >
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
NO
>> Clear DTC. Inspection End.
6.
SEAT BELT PRE-TENSIONER RH
1. Replace the seat belt pre-tensioner RH. Refer to
SR-29, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
RELATED HARNESS
Replace the related harness.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст