Nissan Versa Sedan. Instruction — part 566
MA-22
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
OIL FILTER : Inspection
INFOID:0000000009269055
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to
MA-20, "ENGINE OIL : Inspection"
2. Start the engine and ensure there are no engine oil leaks.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level and adjust as necessary. Refer to
MA-20, "ENGINE OIL : Inspection"
.
SPARK PLUG
SPARK PLUG : Exploded View
INFOID:0000000009269056
SPARK PLUG : Removal and Installation
INFOID:0000000009269057
REMOVAL
1. Remove ignition coil. Refer to
EM-44, "Removal and Installation"
.
CAUTION:
Do not drop or shock ignition coil.
2. Remove spark plug using a suitable tool.
CAUTION:
Do not drop or shock spark plug.
INSPECTION AFTER REMOVAL
CAUTION:
1.
Ignition coil
2.
Spark plug
PBIC3662E
Diameter (a)
: 14 mm (0.55 in)
JPBIA0030ZZ
ENGINE MAINTENANCE
MA-23
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Do not use a wire brush for cleaning.
• If the spark plug tip is covered with carbon, a spark plug cleaner may be used.
• Checking and adjusting spark plug gap is not required between
change intervals. Do not adjust the gap; replace the spark plug as
necessary if out of specification.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not drop or shock the spark plug.
*: Always check with the Parts Department for the latest parts information.
EVAP VAPOR LINES
EVAP VAPOR LINES : Inspection
INFOID:0000000009269058
1. Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration.
2. Inspect fuel tank filler cap vacuum relief valve for clogging, sticking, etc. Refer to
SMA773C
Cleaner air pressure
: Less than 588 kPa (6 kg/cm
2
, 85 psi)
Cleaning time
: Less than 20 seconds
SMA806CA
Make
NGK
Standard type*
PLZKAR6A-11
Gap (nominal)
1.1 mm (0.043 in)
MA-24
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
CHASSIS AND BODY MAINTENANCE
EXHAUST SYSTEM
EXHAUST SYSTEM : Inspection
INFOID:0000000009269059
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leaks, cracks, damage or deterioration. Repair or replace as
necessary.
CVT FLUID
CVT FLUID : Inspection
INFOID:0000000009269060
FLUID LEAKAGE
• Check transaxle surrounding area (oil seal and plug etc.) for fluid
leakage.
• If anything is found, repair or replace damaged parts and adjust
CVT fluid level. Refer to
CVT FLUID : Replacement
INFOID:0000000009269061
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN
CVT Fluid NS-3 will damage the CVT, which is not covered by the (NISSAN new vehicle limited) war-
ranty.
• Always use shop paper. Do not use shop cloth.
• Replace a drain plug gasket with new ones at the final stage of the operation when installing.
• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.
• After replacement, always perform CVT fluid leakage check.
1. Select “Data Monitor” in “TRANSMISSION” using CONSULT.
2. Select “FLUID TEMP” and confirm that the CVT fluid temperature is 40
°C (104°F) or less.
3. Check that the selector lever is in the “P” position, then completely engage the parking brake.
4. Lift up the vehicle.
5. Remove the drain plug and overflow tube and drain the CVT fluid from the oil pan.
.
SMA211A
SMA146B
CVT fluid
: Refer to
TM-456, "General Specification"
Fluid capacity
: Refer to
CHASSIS AND BODY MAINTENANCE
MA-25
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
6. Install the charging pipe set (KV311039S0) (A) into the drain
hole.
CAUTION:
Tighten the charging pipe by hand.
7. Install the ATF changer hose (B) to the charging pipe.
CAUTION:
Press the ATF changer hose all the way onto the charging
pipe until it stops.
8. Fill approximately 3 liter (3-1/8 US qt, 2-5/8 lmp qt) of the CVT
fluid.
9. Remove the ATF changer hose and charging pipe, then install
the drain plug.
NOTE:
Perform this work quickly because CVT fluid leaks.
10. Lift down the vehicle.
11. Start the engine.
12. While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it
to the “P” position.
NOTE:
Hold the lever at each position for 5 seconds.
13. Check that the CONSULT “Data monitor” in “FLUID TEMP” is 35
°C (95°F) to 45°C (113°F).
14. Stop the engine.
15. Lift up the vehicle.
16. Remove the drain plug, and then drain CVT fluid from oil pan.
17. Repeat steps 6 to 16 (one time).
18. Install the overflow tube. Refer to
TM-440, "Removal and Installation"
.
CAUTION:
Be sure to tighten to the specified torque. If it is not tightened to the specified torque, the tube may
be damaged.
19. Install the charging pipe set (KV311039S0) (A) into the drain
hole.
CAUTION:
Tighten the charging pipe by hand.
20. Install the ATF changer hose (B) to the charging pipe.
CAUTION:
Press the ATF changer hose all the way onto the charging
pipe until it stops.
21. Fill approximately 3 liter (3-1/8 US qt, 2-5/8 lmp qt) of the CVT
fluid.
22. Remove the ATF changer hose and charging pipe, then install
the drain plug.
NOTE:
Perform this work quickly because CVT fluid leaks.
23. Lift down the vehicle.
24. Start the engine.
25. While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it
to the “P” position.
NOTE:
Hold the lever at each position for 5 seconds.
26. Check that the CONSULT “Data monitor” in “FLUID TEMP” is 35
°C (95°F) to 45°C (113°F).
27. Lift up the vehicle.
28. Remove the drain plug and confirm that the CVT fluid is drained from the overflow tube.
CAUTION:
Perform this work with the vehicle idling.
NOTE:
JSDIA1876ZZ
JSDIA1876ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст