Nissan Altima L32. Instruction — part 1609
FRONT WIPER DOES NOT OPERATE
WW-109
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Is the measurement normal?
YES LO circuit>>Refer to
YES HI circuit>>Refer to
NO
>> Replace IPDM E/R. Refer to
PCS-48, "Removal and Installation"
.
5.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "FR WIP REQ" of IPDM E/R "DATA MONITOR" item.
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the monitor status.
Is the status of item normal?
YES
>> Replace IPDM E/R. Refer to
PCS-48, "Removal and Installation"
.
NO
>> GO TO 6
6.
CHECK COMBINATION SWITCH
1. Perform the inspection of the combination switch. Refer to
Is combination switch normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
NO
>> Repair or replace the malfunctioning parts.
Terminals
Test item
Voltage (V)
(Approx.)
(+)
(-)
IPDM E/R
Ground
FRONT WIPER
Connector
Terminal
E18
4
Lo
Battery
voltage
Off
0 V
5
Hi
Battery
voltage
Off
0 V
Monitor item
With operating the front wiper
switch condition
Monitor status
FR WIP REQ
Front wiper
switch HI
ON
Hi
OFF
Stop
Front wiper
switch LO
ON
Low
OFF
Stop
WW-110
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000004202211
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.
PRECAUTIONS
WW-111
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN-
SIONER
INFOID:0000000004202212
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004513177
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
WW-112
< ON-VEHICLE REPAIR >
FRONT WIPER
ON-VEHICLE REPAIR
FRONT WIPER
Exploded View
INFOID:0000000004202215
FRONT WIPER BLADE REFILL
FRONT WIPER BLADE REFILL : Removal and Installation
INFOID:0000000004202216
REMOVAL
1. Remove the front wiper blade. Refer to
WW-115, "FRONT WIPER BLADE : Removal and Installation"
.
1.
Rib (part of wiper blade refill)
2.
Wiper blade refill
3.
Front RH wiper blade assembly (in-
cludes wiper blade refill)
4.
Front RH wiper arm
5.
Wiper arm cap
6.
Front wiper drive assembly
7.
Front LH wiper blade assembly (in-
cludes wiper blade refill)
8.
Front LH wiper arm
Front
AWLIA1564GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст