Nissan Altima L32. Instruction — part 1610
FRONT WIPER
WW-113
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
2. Hold the wiper blade refill lip at the end (A) of the front wiper
blade (1) with a suitable tool (B) as shown, and pull it firmly in
the direction (C).
• U clip (part of the front wiper blade assembly) (D)
• If the wiper blade refill lip is torn due to wear, insert a suitable
tool (A) into the space between the end of the wiper blade refill
(1) and the front wiper blade (2) and pull the wiper blade refill
(1) out as shown.
INSTALLATION
1. If the rib (A) has become detached from the wiper blade refill (1),
check that the curve of the rib (A) is in the same direction as the
curve of the wiper blade refill (1) and insert the rib (A) into the slit
(B) in the wiper blade refill (1) as shown.
ALLIA0860ZZ
ALLIA0861ZZ
ALLIA0866ZZ
WW-114
< ON-VEHICLE REPAIR >
FRONT WIPER
• If the rib (A) has a notch (B), insert the rib (A) into the wiper
blade refill (1) so the notch (B) fits over the protrusion (C) in
the wiper blade refill (1) as shown.
2. Insert the wiper blade refill (1) tip into the end of the front wiper
blade (2) in the direction (C). Push the wiper blade refill (1) in
while pressing it into the end of the front wiper blade (2) as
shown. After the wiper blade refill is fully inserted, remove the
holder (B).
• Tab [part of front wiper blade (2)] (A)
• Make sure to slide the refill into the front wiper blade so that
the wiper blade refill is held by the tabs (A) on the front wiper
blade as shown.
ALLIA0867ZZ
ALLIA0862ZZ
ALLIA0863ZZ
FRONT WIPER
WW-115
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
3. Push the wiper blade refill (1) until the tabs on the front wiper
blade (2) fit into the stoppers (A) in the end of the wiper blade
refill (1). Make sure the LOCK mark (B) on the wiper blade refill
(1) is aligned with the lock point symbol (C) on the front wiper
blade (2) as shown.
4. Before installing the front wiper blade assembly, make sure that
the wiper blade refill (1) end is fully covered by the front wiper
blade (2) in area (A) as shown.
5. Install the front wiper blade. Refer to
WW-115, "FRONT WIPER BLADE : Removal and Installation"
.
FRONT WIPER BLADE
FRONT WIPER BLADE : Removal and Installation
INFOID:0000000004202217
REMOVAL
1. Lift the front wiper arm and wiper blade assembly away from the windshield.
2. Rotate the front wiper blade assembly and push the release tab
(A), then move the front wiper blade assembly down (B) the
front wiper arm.
3. Remove the front wiper blade assembly.
INSTALLATION
CAUTION:
• After the front wiper blade assembly installation, return the front wiper arm to the original position
on the windshield to prevent damage when the hood is opened.
ALLIA0864ZZ
ALLIA0865ZZ
AWLIA1565ZZ
WW-116
< ON-VEHICLE REPAIR >
FRONT WIPER
• Check that the front wiper blade assembly contacts the windshield properly; otherwise the front
wiper arm may be damaged from wind pressure while driving.
1. Insert the front wiper blade assembly onto the front wiper arm and slide it up until it clicks into place.
2. Rotate the front wiper blade assembly so the dimple is in the groove.
3. Lay the front wiper arm and front wiper blade assembly back down on the windshield.
FRONT WIPER ARMS
FRONT WIPER ARMS : Removal and Installation
INFOID:0000000004202218
REMOVAL
1. Turn wiper switch ON to operate wiper motor, and then turn wiper switch OFF (auto stop).
2. Open hood, remove arm caps, and remove wiper arm nuts.
3. Raise wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1. Clean up the pivot area as shown. This will reduce possibility of
wiper arm looseness.
2. Prior to wiper arm installation, turn on wiper switch to operate wiper motor and then turn it “OFF” (auto
stop).
3. Push wiper arm onto pivot shaft, paying attention to blind spline.
4. Lift the blade up and then set it down onto glass surface to set
the blade center to clearance "A", "B", "C" and "D" immediately
before temporarily tightening the wiper arm nuts.
5. Spray washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
6. Make sure that wiper blades stop within clearance "A", "B", "C"
and "D".
7. Tighten wiper arm nuts to specification. Refer to
.
8. Attach wiper arm caps.
ADJUSTMENT
To adjust the wiper arm stop location, the wiper arm must be removed and installed. Refer to
"FRONT WIPER ARMS : Removal and Installation"
FRONT WIPER DRIVE ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY : Removal and Installation
INFOID:0000000004202219
REMOVAL
1. Operate front wiper motor, and stop at the auto stop position.
SEL024J
Clearance “A”
: 41.3
± 7.5 mm (1.626 ± 0.295 in)
Clearance “B”
: 65.5
± 7.5 mm (2.579 ± 0.295 in)
Clearance “C”
: 27.8 mm (1.094 in)
Clearance “D”
: 53.7 mm (2.114 in)
BKIA0254E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст