Nissan Altima L32. Instruction — part 759
FRONT WHEEL HUB AND KNUCKLE
FAX-9
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
7. Disconnect the outer tie-rod end from steering knuckle using
Tool. Be careful not to damage ball joint boot.
CAUTION:
To prevent damage to threads and to prevent Tool from
coming off suddenly, temporarily tighten mounting nut.
8. Remove transverse link and steering knuckle pinch bolt and nut using power tool. Refer to
9. Remove wheel hub and bearing assembly from drive shaft using
a puller or suitable tool.
CAUTION:
• When removing wheel hub and bearing assembly, do not
apply an excessive angle to drive shaft joint. Also be care-
ful not to excessively extend slide joint.
• Support drive shaft when removing.
10. Remove wheel hub and bearing assembly bolts using power tool.
11. Remove splash guard and wheel hub and bearing assembly from steering knuckle.
12. Remove the lower strut bolts and nuts using power tool. Refer to
.
13. Remove steering knuckle from vehicle.
INSPECTION AFTER REMOVAL
Check for deformity, cracks and damage on each part, replace if necessary.
Ball Joint Inspection
• Check for boot breakage, axial looseness, and torque of transverse link ball joint and repair as necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse non-reusable parts.
• When installing wheel hub and bearing assembly to steering knuckle, align cutout in toner ring cover with
wheel sensor mounting hole in steering knuckle.
Tool number
: HT72520000 (J-25730-A)
WGIA0101E
SDIA0972J
AFA047
FAX-10
< ON-VEHICLE REPAIR >
FRONT WHEEL HUB AND KNUCKLE
• When installing disc rotor on wheel hub and bearing assembly,
align the marks.
(When not using the alignment mark, refer to
SDIA1480E
FRONT DRIVE SHAFT
FAX-11
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Removal and Installation (Left Side)
INFOID:0000000004205631
REMOVAL
1. Remove wheel and tire. Refer to
.
2. Remove wheel sensor from steering knuckle. Refer to
BRC-63, "Removal and Installation"
134, "Removal and Installation"
BRC-236, "Removal and Installation"
(VDC/TCS/ABS).
3. Remove cotter pin. Then remove lock nut from drive shaft.
4. Remove brake hose lock plate. Then remove brake hose from strut.
5. Remove the lower ball joint pinch bolt using power tool, then separate lower ball joint from steering
6. Remove drive shaft from wheel hub and bearing assembly,
using a puller or suitable tool.
CAUTION:
• When removing drive shaft, do not apply an excessive
angle to drive shaft joint. Also be careful not to exces-
sively extend slide joint.
7. Remove the lefthand drive shaft from the transaxle.
• Remove drive shaft from transaxle using Tool and drive shaft
puller or suitable tool.
- Set Tool and a drive shaft puller or suitable tool between drive
shaft (slide joint side) and transaxle as shown, then remove
drive shaft.
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in axial direction. Check for any rough movement or significant looseness.
1.
Drive shaft
2.
Cotter pin
AWDIA0573GB
SDIA0972J
Tool number
: KV40107500 ( — )
WDIA0098E
FAX-12
< ON-VEHICLE REPAIR >
FRONT DRIVE SHAFT
• Check boot for cracks or other damage, and for grease leakage.
• If damaged, disassemble drive shaft to verify damage, and repair
or replace as necessary.
INSTALLATION
Installation is in the reverse order of removal. Note the following:
CAUTION:
Do not reuse non-reusable parts.
• In order to prevent damage to differential side oil seal, place Tool
(A) onto oil seal before inserting drive shaft as shown. Slide drive
shaft into slide joint and tap with a hammer to install securely.
• Install new circlip on drive shaft in the circular clip groove on tran-
saxle side. Refer to
FAX-15, "Disassembly and Assembly (Left
.
CAUTION:
Make sure the new circlip on the drive shaft is securely fas-
tened.
• After its insertion, try to pull the flange out of the slide joint by hand.
If it pulls out, the circlip is not properly meshed with the transaxle side gear.
Removal and Installation (Right Side)
INFOID:0000000004205632
WDIA0369E
Tool number : KV38106700 (J-34296)
WDIA0298E
AWDIA0635GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст