Nissan Altima L32. Instruction — part 1417

TM-12

< PRECAUTION >

[6MT: RS6F52A]

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000004201575

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Man-

ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by

an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

ness connectors.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000004201576

When performing the procedure after removing cowl top cover, cover

the lower end of windshield with urethane, etc.

Service Notice or Precautions

INFOID:0000000004201577

• Do not reuse transaxle oil, once it has been drained.

• Check oil level or replace oil with vehicle on level surface.

• During removal or installation, keep inside of transaxle clear of dust or dirt.

• Check for the correct installation status prior to removal or disassembly. If matching marks are required, be

certain they do not interfere with the function of the parts they are applied.

• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tight-

ening sequence is specified, use it.

• Be careful not to damage sliding surfaces and mating surfaces.

PIIB3706J

PREPARATION

TM-13

< PREPARATION >

[6MT: RS6F52A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000004201578

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

KV381054S0
(J-34286)
Puller

• Removing differential side bearing outer

race

• Removing mainshaft front bearing

ST33400001
(J-26082)
Drift

Installing differential side oil seal (clutch hous-
ing side)
a: 60 mm (2.36 in) dia.
b:47 mm (1.85 in) dia.

ST35321000
(

—

)

Drift

• Installing input shaft oil seal
• Installing reverse main gear
• Installing 1st main gear bushing
• Installing 1st-2nd synchronizer hub assem-

bly

• Installing 2nd main gear bushing
• Installing 3rd main gear
a: 49 mm (1.93 in) dia.
b: 41 mm (1.61 in) dia.

ST33200000
(J-26082)
Drift

• Installing mainshaft front bearing
• Installing 6th input gear bushing
• Installing 4th main gear
• Installing 5th main gear
• Installing 6th main gear
a: 60 mm (2.36 in) dia.
b: 44.5 mm (1.752 in) dia.

ST30720000
(J-25405)
Drift

• Installing differential side oil seal (transaxle

case side)

• Installing differential side bearing outer race

(transaxle case side)

• Installing mainshaft rear bearing
• Installing differential side bearing
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.

ST33061000
(J-8107-2)
Drift

• Installing bore plug
• Removing differential side bearing (transax-

le case side)

• Removing differential side bearing (clutch

housing side)

a: 38 mm (1.50 in) dia.
b: 28.5 mm (1.122 in) dia.

ZZA0601D

ZZA0814D

ZZA1000D

ZZA1002D

ZZA0811D

ZZA1000D

TM-14

< PREPARATION >

[6MT: RS6F52A]

PREPARATION

ST33052000
(

—

)

Drift

• Removing input shaft rear bearing
• Removing 5th input gear bushing, 4th input

gear, 4th input gear bushing, 3rd-4th syn-
chronizer hub assembly, and 3rd input gear

• Installing input shaft front bearing
• Removing mainshaft rear bearing
• Removing 6th main gear
• Removing 4th main gear and 5th main gear
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.

KV40105020
(

—

)

Drift

• Removing 5th input gear and 5th-6th syn-

chronizer hub assembly

• Removing 3rd main gear, 2nd main gear,

2nd main gear bushing, 1st-2nd synchroniz-
er hub assembly, 1st main gear, 1st main
gear bushing, and reverse main gear

a: 39.7 mm (1.563 in) dia.
b: 35 mm (1.38 in) dia.
c: 15 mm (0.59 in)

ST30031000
(J-22912-01)
Puller

Measuring wear of inner baulk ring

KV40105710
(

—

)

Press stand

• Installing 3rd-4th synchronizer hub assem-

bly

• Installing 4th input gear bushing
• Installing 5th input gear bushing
• Installing 5th-6th synchronizer hub assem-

bly

• Installing 2nd main gear bushing
• Installing 3rd main gear
a: 46 mm (1.81 in) dia.
b: 41 mm (1.61 in)

ST30901000
(J-26010-01)
Drift

• Installing input shaft rear bearing
• Installing 4th main gear
• Installing 5th main gear
• Installing 6th main gear
• Installing mainshaft rear bearing
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.

ST30032000
(J-26010-01)
Drift

Installing input shaft front bearing
a: 80 mm (3.15 in) dia.
b: 38 mm (1.50 in) dia.
c: 31 mm (1.22 in) dia.

Tool number
(Kent-Moore No.)
Tool name

Description

ZZA1023D

ZZA1133D

ZZA0537D

ZZA1058D

ZZA0978D

ZZA0978D

PREPARATION

TM-15

< PREPARATION >

[6MT: RS6F52A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Commercial Service Tools

INFOID:0000000004201579

ST38220000
(

—

)

Press stand

• Installing reverse main gear
• Installing 1st main gear bushing
• Installing 1st-2nd synchronizer hub assem-

bly

a: 63 mm (2.48 in) dia.
b: 65 mm (2.56 in)

KV40101630
(J-35870)
Drift

Installing reverse main gear
a: 68 mm (2.68 in) dia.
b: 60 mm (2.36 in) dia.

KV38102510
(

—

)

Drift

• Installing 1st main gear bushing
• Installing 1st-2nd synchronizer hub assem-

bly

• Installing differential side bearing (transaxle

case side)

• Installing differential side bearing (clutch

housing side)

a: 71 mm (2.80 in) dia.
b: 65 mm (2.56 in) dia.

(

—

)

(J-39713)
Preload adapter

Measuring end play of side gear

Tool number
(Kent-Moore No.)
Tool name

Description

ZZA1058D

ZZA1003D

ZZA0838D

NT087

Tool name

Description

Pin punch

Removing and installing retaining pin
a: 4.5 mm (0.177 in) dia.

Pin punch

Removing and installing retaining pin of selec-
tor lever
a: 5.5 mm (0.217 in) dia.

NT410

NT410