Nissan Altima L32. Instruction — part 1418
TM-16
< PREPARATION >
[6MT: RS6F52A]
PREPARATION
Pin punch
Removing and installing retaining pin of each
shifter lever
a: 7.5 mm (0.295 in) dia.
Drift
Installing striking rod oil seal and shifter lever
oil seal
a: 24.5 mm (0.965 in) dia.
Puller
Removing each bearing, gear, and bushing
Puller
Removing each bearing, gear, and bushing
Power tool
Loosening bolts and nuts
Tool name
Description
NT410
S-NT063
ZZA0537D
NT077
PBIC0190E
M/T OIL
TM-17
< ON-VEHICLE MAINTENANCE >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE MAINTENANCE
M/T OIL
Draining
INFOID:0000000004201580
1. Start engine and let it run to warm up transaxle oil.
2. Stop engine and remove the drain plug to drain the oil.
3. Install the drain plug with a new gasket to the transaxle case. Tighten the drain plug to the specified
.
CAUTION:
Do not reuse gasket.
Refilling
INFOID:0000000004201581
1. Remove the filler plug (1) and fill transaxle with new oil.
2. After refilling oil, measure oil level to check if it is within the spec-
ification using suitable gauge (A) as shown.
CAUTION:
• Do not start engine while checking oil level.
• Insert the suitable gauge straight and against the wall of
the filler plug hole, then measure the gauge from the top
of the filler plug hole to the oil level as shown.
3. Install the filler plug with a new O-ring to the clutch housing.
CAUTION:
Do not reuse O-ring.
4. Tighten filler plug bolt to the specified torque. Refer to
.
Inspection
INFOID:0000000004201582
LEAKAGE
• Make sure that oil is not leaking from transaxle or around it.
LEVEL
1. Remove the filler plug (1).
2. Measure oil level to check if it is within the specification using a
suitable gauge (A) as shown.
CAUTION:
• Do not start engine while checking oil level.
• Insert the suitable gauge straight and against the wall of
the filler plug hole, then measure the gauge from the top
of the filler plug hole to the oil level as shown.
3. Install the filler plug with a new O-ring to the clutch housing.
CAUTION:
Do not reuse O-ring.
4. Tighten the filler plug bolt to the specified torque. Refer to
.
Oil grade
: Refer to
MA-12, "Fluids and Lubricants"
Oil level “L” : Refer to
TM-82, "General Specifications"
.
JPDIC0138ZZ
Oil level “L” : Refer to
.
JPDIC0138ZZ
TM-18
< ON-VEHICLE REPAIR >
[6MT: RS6F52A]
SIDE OIL SEAL
ON-VEHICLE REPAIR
SIDE OIL SEAL
Removal and Installation
INFOID:0000000004201583
REMOVAL
1. Remove the drive shaft. Refer to
FAX-11, "Removal and Installation (Left Side)"
,
2. Remove oil seal using suitable tool.
CAUTION:
Do not damage the transaxle case surface when removing
oil seal.
INSTALLATION
1. Drive the oil seal straight into the transaxle case and clutch
housing to the specified dimension "A" using Tools.
CAUTION:
Do not reuse oil seal.
2. Install the drive shaft. Refer to
FAX-11, "Removal and Installa-
FAX-12, "Removal and Installation (Right
.
3. Check the transaxle fluid level. Refer to
.
SCIA0824E
Dimension “A” : 0
±± 0.5 mm (0 ± 0.020 in)
Tool numbers
: ST30720000 (J–25405)
: ST33400001 (J-26082)
SCIA1010E
BACK-UP LAMP SWITCH
TM-19
< ON-VEHICLE REPAIR >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
BACK-UP LAMP SWITCH
Removal and Installation
INFOID:0000000004201584
For removal and installation of back-up lamp switch, refer to
Inspection
INFOID:0000000004201585
• Check continuity.
Gear position
Continuity
Reverse
Yes
Except reverse
No
SCIA0708E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст