Nissan Altima L32. Instruction — part 1522
TM-432
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
CONTROL DEVICE
Inspection and Adjustment
INFOID:0000000004202006
INSPECTION
1. Place selector lever in “P” position, and turn ignition switch ON (engine stop).
2. Make sure that selector lever can be shifted to other than “P” position when brake pedal is depressed.
Also make sure that selector lever can be shifted from “P” position only when brake pedal is depressed.
3. Move the selector lever and check for excessive effort, sticking, noise or rattle.
4. Confirm the selector lever stops at each position with the feel of engagement when it is moved through all
the positions. Check that the actual position of the selector lever matches the position shown by the shift
position indicator and the instruction lever on the transaxle.
5. The method of operating the selector lever to individual posi-
tions correctly should be as shown.
6. When selector button is pressed in “P”, “R”, or “N” position with-
out applying forward/backward force to selector lever, check but-
ton operation for sticking.
7. Confirm the back-up lamps illuminate only when selector lever is
placed in the “R” position. Confirm the back-up lamps do not illu-
minate when the selector lever is pushed toward the “R” position
when in the “P” or “N” position.
8. Confirm the engine can only be started with the selector lever in
the “P” and “N” positions.
9. Make sure transaxle is locked completely in “P” position.
10. When selector lever is set to instruction shift gate, make sure that manual mode is displayed on combination
meter.
Shift selector lever to “+” and “-” sides, and check that set shift position changes.
ADJUSTMENT
CAUTION:
Apply parking brake before adjustment.
1. Loosen the control cable nut.
2. Place the instruction lever and the selector lever in “P” position.
3. Tighten control cable nut to specified torque.
CAUTION:
Secure the instruction lever when tightening control cable nut. Make sure the manual lever stays in
the "P" position.
4. Check the operation of the CVT. Refer to
TM-432, "Inspection and Adjustment"
.
SCIA6760E
Control cable nut: Refer to
.
CONTROL CABLE
TM-433
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL CABLE
Exploded View
INFOID:0000000004202007
Removal and Installation
INFOID:0000000004202008
REMOVAL
1. Shift control lever to "P".
2. Remove the air filter assembly. Refer to
EM-25, "Removal and Installation"
3. Remove the control cable nut and control cable form the instruction lever.
4. Remove the lock plate and the control cable from the bracket.
5. Remove the center console. Refer to
IP-12, "Removal and Installation"
.
6. Remove the bracket covering the retainer grommet.
7. Remove the retainer grommet bolts and the retainer grommet.
8. Remove the control cable from the control device assembly.
9. Remove the control cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the control cable to the control device assembly, make sure that the control cable socket is
fully pressed into the control device assembly, and the control cable end is fully pressed in with the ribbed
surface facing upward.
• After installation is complete, adjust and check the CVT position. Refer to
TM-432, "Inspection and Adjust-
.
1.
Control lever
2.
Control device assembly
3.
Control cable socket
4.
Retainer grommet
5.
Control cable
6.
Bracket
7.
Lock plate
8.
Instruction lever
ALDIA0027GB
TM-434
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000004202009
Removal and Installation
INFOID:0000000004202010
REMOVAL
1. Remove drive shaft assembly. Refer to
and
FAX-12, "Removal and Installation
.
2. Remove the differential side oil seal using suitable tool
CAUTION:
Do not scratch transaxle case or converter housing.
INSTALLATION
1. Drive the new differential side oil seal into the transaxle case
side (B) and converter housing side (C) until it is flush using
Tool.
CAUTION:
• Do not reuse differential side oil seals.
• Apply specified NISSAN CVT fluid to side oil seals.
2. Install drive shaft assembly. Refer to
FAX-12, "Removal and Installation (Right Side)"
.
3. Check CVT fluid level. Refer to
1.
CVT assembly
2.
Differential side oil seal
:NISSAN CVT Fluid NS-2
ALDIA0047GB
SCIA2412E
Tool number
: KV38100300 ( — )
Dimension A
: 1.8
± 0.5 mm (0.071 ± 0.020 in)
WCIA0598E
AIR BREATHER HOSE
TM-435
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000004202011
Removal and Installation
INFOID:0000000004202012
Refer to the figure for removal and installation.
CAUTION:
• Install air breather hose with paint mark facing upward.
• Insert air breather hose a minimum of 17mm (0.67 in) onto air breather tube (to end of air breather
tubes radius end).
• Install air breather hose to bracket by fully inserting the clip.
• Make sure there are no pinched or restricted areas on air breather hose caused by bending or wind-
ing when installing it.
1.
Air breather hose
2.
Clip
3.
Bracket
4.
Air breather tube
5.
CVT assembly
A.
Paint mark
⇐: Front
ALDIA0037ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст