Nissan Altima L32. Instruction — part 652
EM-144
< ON-VEHICLE REPAIR >
[VQ35DE]
OIL PAN AND OIL STRAINER
9. Install the lower oil pan. Tighten the lower oil pan bolts in order
as shown.
• Wait at least 30 minutes before refilling the engine with oil.
10. Install rear plate cover.
11. Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
• Start the engine and check for leaks. Refer to
.
• Inspect the engine oil level. Refer to
WBIA0261E
SEM717G
IGNITION COIL
EM-145
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
IGNITION COIL
Exploded View
INFOID:0000000004505028
Removal and Installation LH
INFOID:0000000004505029
REMOVAL
1. Remove engine room cover.
2. Disconnect ignition coil connector.
3. Remove the ignition coil.
CAUTION:
Never shock ignition coil.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation RH
INFOID:0000000004505030
REMOVAL
1. Remove the intake manifold collector. Refer to
EM-130, "Removal and Installation"
2. Disconnect ignition coil connector.
3. Remove the ignition coil.
CAUTION:
Never shock ignition coil.
INSTALLATION
Installation is in the reverse order of removal.
1.
Ignition coil
2.
Spark plug
3.
Rocker cover (RH)
4.
Rocker cover (LH)
AWBIA0203GB
EM-146
< ON-VEHICLE REPAIR >
[VQ35DE]
FUEL INJECTOR AND FUEL TUBE
FUEL INJECTOR AND FUEL TUBE
Removal and Installation
INFOID:0000000004202164
CAUTION:
• Apply new engine oil when installing the parts as specified to do so.
• Do not remove or disassemble parts unless instructed as shown.
REMOVAL
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
• To avoid the danger of being scalded, never drain engine coolant when engine is hot.
1. Remove engine cover.
2. Release the fuel pressure. Refer to
.
3. Remove front wiper arm and extension cowl top. Refer to
EXT-18, "Removal and Installation"
EXT-39, "Removal and Installation"
(Sedan models).
JPBIA2526GB
1.
Fuel feed hose
2.
Quick connector cap
3.
Fuel tube
4.
O-ring
5.
Fuel damper
6.
Fuel damper cap
7.
Clip
8.
O-ring (black)
9.
Fuel injector
10. O-ring (green)
A.
Follow installation procedure
FUEL INJECTOR AND FUEL TUBE
EM-147
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4. Remove the electric throttle control actuator bolts in the reverse
order as shown and remove the electric throttle control actuator.
CAUTION:
• Handle carefully to avoid any shock to the electric throttle
control actuator.
• Do not disassemble.
5. Remove intake manifold collector. Refer to
EM-130, "Removal and Installation"
6. When separating fuel feed hose and fuel tube connection, disconnect quick connector as follows:
a. Remove quick connector cap from quick connector.
b. Disconnect quick connector from fuel tube as follows:
CAUTION:
Disconnect quick connector by using the quick connector release (commercial service tool: J-
45488), not by picking out retainer tabs.
i.
With the sleeve side of quick connector release facing to quick connector, install the quick connector
release onto fuel tube.
ii.
Insert the quick connector release (A) into quick connector (2)
until sleeve (B) contacts and goes no further. Hold quick connec-
tor release on that position.
CAUTION:
Inserting quick connector release hard will not disconnect
quick connector. Hold quick connector release where it
contacts and goes no further.
iii. Draw and pull out quick connector straight from fuel tube (1).
CAUTION:
• Pull quick connector (E) holding position (D) as shown in
the figure.
• Never pull with lateral force applied. O-ring inside quick connector may be damaged.
• Prepare container and cloth beforehand as fuel will leakage out.
• Avoid fire and sparks.
• Keep parts away from heat source. Especially, be careful when welding is performed around
them.
• Never expose parts to battery electrolyte or other acids.
• Never bend or twist connection between quick connector and fuel feed hose (with damper) dur-
ing installation/removal.
• To keep clean the connecting portion and to avoid dam-
age and foreign materials, cover them completely with
plastic bags, etc. (A) or something similar.
7. Disconnect harness connector from fuel injector.
SEM711G
C
: Insert and retain
JPBIA0033ZZ
JPBIA0035ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст