Nissan Altima L32. Instruction — part 651
EM-140
< ON-VEHICLE REPAIR >
[VQ35DE]
OIL PAN AND OIL STRAINER
12. Remove the oil filter and engine oil cooler from the upper oil pan.
13. Remove the oil pressure switch, and the crankshaft position sensor (POS) from the upper oil pan.
14. Remove the front drive shaft (RH). Refer to
FAX-12, "Removal and Installation (Right Side)"
15. Disconnect the heated oxygen sensors and air flow ratio (A/F) sensors and remove the two catalytic con-
vertors from the exhaust manifolds using power tool. Refer to
EM-136, "Removal and Installation"
16. Remove the rear plate cover from the upper oil pan.
17. Loosen the lower oil pan bolts using power tool in order as
shown. Remove the lower oil pan.
a. Insert Tool between the lower oil pan and the upper oil pan.
• Be careful not to damage the mating surface.
• Do not insert a screwdriver, this will damage the mating sur-
faces.
b. Slide (2) the Tool by tapping (1) its side with a hammer to
remove the lower oil pan from the upper oil pan.
18. Remove the four upper oil pan to transaxle bolts.
SEM717G
WBIA0258E
Tool number
: KV10111100 (J37228)
WBIA0566E
SEM469G
OIL PAN AND OIL STRAINER
EM-141
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
19. Remove the upper oil pan.
a. Loosen the bolts in the order as shown, using power tool.
b. Insert an appropriate size tool into the notch (1) of the upper oil
pan as shown.
c. Pry off the upper oil pan by moving the tool up and down (2) as
shown.
20. Remove the O-ring seals from the bottom of the cylinder block
and oil pump housing, use new O-rings for installation.
21. Remove front cover gasket and rear oil seal retainer gasket.
22. Remove the oil strainer.
LBIA0358E
SEM155F
WBIA0327E
WBIA0328E
EM-142
< ON-VEHICLE REPAIR >
[VQ35DE]
OIL PAN AND OIL STRAINER
23. If re-installing the original oil pan, remove the old sealant from
the mating surfaces using a scraper.
• Also remove the old sealant from mating surface of the cylin-
der block.
• Remove the old sealant from the bolt holes and threads.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off the old sealant.
INSPECTION AFTER REMOVAL
Clean oil strainer if any object is attached.
INSTALLATION
CAUTION:
Wait at least 30 minutes before refilling the engine with oil.
1. Install oil strainer and tighten bolt to specified torque. Refer to
EM-139, "Removal and Installation"
.
2. Apply Genuine Silicone RTV Sealant or equivalent, to the front
cover gasket and the rear oil seal retainer gasket as shown.
Refer to
GI-15, "Recommended Chemical Products and Seal-
.
3. Install the front cover gasket and rear oil seal retainer gasket as
shown.
4. Apply a bead of sealant to the cylinder block mating surface of
the upper oil pan to a limited portion as shown.
• Use Genuine Silicone RTV Sealant, or equivalent. Refer to
15, "Recommended Chemical Products and Sealants"
.
• Be sure the sealant is applied to a limited portion as shown,
and the sealant is 4.0 - 5.0 mm (0.157 - 0.197 in) or 4.5 - 5.5
mm (0.177 - 0.217 in) wide.
• Attaching should be done within 5 minutes after coating.
MEM108A
SEM964E
WBIA0328E
SEM185FA
OIL PAN AND OIL STRAINER
EM-143
< ON-VEHICLE REPAIR >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
5. Install new O-rings on the cylinder block and oil pump body.
6. Install the upper oil pan.
• Tighten upper oil pan bolts in the order as shown.
• Wait at least 30 minutes before refilling the engine with oil.
7. Install the four upper oil pan to transaxle bolts.
8. Apply a continuous bead of sealant to the lower oil pan.
• Use Genuine Silicone RTV Sealant, or equivalent. Refer to
15, "Recommended Chemical Products and Sealants"
.
• Be sure the sealant is 4.5 - 5.5 mm (0.177 - 0.217 in) wide.
• Installation must be done within 5 minutes after applying seal-
ant.
SEM159F
WBIA0327E
LBIA0359E
SEM469G
SEM159F
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст