Nissan Altima L32. Instruction — part 1525
TM-444
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
CONTROL VALVE
6. Fix the control valve using the control valve bolts (A) and (B).
7. Pull the linkage fixing pin out.
8. Connect the connectors (A) and (B).
CAUTION:
• Never pinch the harness into between the control valve
and the transaxle case.
• Securely insert the connector until it clicks and locks.
9. Install the bracket (1).
10. Install the oil strainer assembly (1) using the oil strainer assem-
bly bolts (A) and (B).
CAUTION:
• Never reuse O-ring.
• Apply NISSAN CVT fluid NS-2 when installing the O-ring.
NOTE:
Remove the bracket and adjust the position again if the bolt hole positions are not aligned.
11. Install the collar to the instruction shaft.
CAUTION:
Never drop the collar.
Front of vehicle
Bolt
Nominal length (mm)
Quantity
A
54
10
B
44
1
JPDIA0659ZZ
Clips
Front of vehicle
JPDIA0656ZZ
Bolt
Front of vehicle
JPDIA0658ZZ
Front of vehicle
Bolt
Nominal length (mm)
Quantity
A
12
2
B
44
1
JPDIA0657ZZ
CONTROL VALVE
TM-445
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
12. Assemble the instruction plate (1) while aligning with the groove (A)
of the instruction valve, and then tighten washer (2) the lock nut (3)
to the specified torque.
CAUTION:
Assemble the instruction plate while aligning its end with the
cutout (
) of the instruction valve.
13. Install the snap ring of CVT unit connector, and then connect the
CVT unit harness connector.
14. Install the magnet while aligning it with the convex side of oil
pan.
CAUTION:
Completely eliminate the iron powder from the magnet area of oil pan and the magnet.
15. Install the oil pan gasket to the oil pan.
CAUTION:
• Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt
hole of oil pan and transaxle case.
• Never reuse oil pan gaskets.
16. Install the oil pan assembly to the transaxle case with the following procedure.
1. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolt.
CAUTION:
Never reuse oil pan bolts.
2. Tighten the oil pan bolts in the order shown to the specified
torque.
3. Tighten the oil pan bolts again clockwise from (1) shown to
the specified torque.
17. Fill CVT fluid from CVT fluid charging pipe to the specified level.
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Never mix with other fluid.
• Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and
CVT durability, and may damage the CVT, which is not covered by the warranty.
• When filling CVT fluid, take care not to scatter heat generating parts such as exhaust.
• Sufficiently shake the container of CVT fluid before using.
• Delete CVT fluid deterioration date with CONSULT-III after changing CVT fluid. Refer to TM-
xx,"CONSULT-III Function (TRANSMISSION)".
18. With the engine warmed up, drive the vehicle in an urban area.
NOTE:
When ambient temperature is 20
°C (68°F), it takes about 10 minutes for the CVT fluid to warm up to 50°
to 80
°C (122° to 176°F).
19. Check CVT fluid level and condition. Refer to
.
20. Connect negative battery terminal. Refer to
PG-68, "Removal and Installation"
Inspection and Adjustment
INFOID:0000000004507228
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
Front of vehicle
CVT fluid
: Refer to
Fluid capacity
: Refer to
JPDIA0962ZZ
JPDIA0664ZZ
TM-446
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
CONTROL VALVE
INSPECTION AFTER REMOVAL
Check the CVT fluid level and leakage. Refer to
INSPECTION AFTER INSTALLATION
Erase the TCM data.
• Erase the CVT fluid degradation level data using CONSULT-III. Refer to
• Erase the memory of ROM using CONSULT-III. Refer to
TM-298, "CONSULT-III Function (TRANSMIS-
.
TRANSAXLE ASSEMBLY
TM-447
< REMOVAL AND INSTALLATION >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000004202023
Removal and Installation
INFOID:0000000004202024
REMOVAL
1. Remove the engine and transaxle as an assembly. Refer to
EM-72, "Removal and Installation"
NOTE:
Using paint, put matching marks on the drive plate and torque converter when removing the torque con-
verter to drive plate nuts.
1.
Air breather hose
2. CVT fluid level gauge
3. CVT fluid charging pipe
4.
O-ring
5. Copper washer
6. Fluid cooler tube
7.
Fluid cooler tube
8. CVT assembly
A.
TM-447, "Removal and Installation"
ALDIA0038GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст