Nissan Altima L32. Instruction — part 1524
TM-440
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
CONTROL VALVE
CONTROL VALVE
Exploded View
INFOID:0000000004507226
COMPONENT PARTS LOCATION
Removal and Installation
INFOID:0000000004507227
REMOVAL
1. Disconnect negative battery terminal. Refer to
PG-68, "Removal and Installation"
2. Pump out CVT fluid from CVT charging pipe.
1.
Transaxle assembly
2.
Control valve
3.
Bracket
4.
O-ring
5.
Oil strainer assembly
6.
Magnet
7.
Oil pan bolt
8.
Oil pan
9.
Oil pan gasket
10.
Lock nut
11. Washer
12. Instruction plate
13.
Collar
14. Lip seal
15. Snap ring
A.
CVT unit connector
For the following symbols, use the specified fluid.
NISSAN CVT Fluid NS-2
AWDIA0636GB
CONTROL VALVE
TM-441
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Disconnect the CVT unit connector. Refer to
TM-411, "Removal and Installation Procedure for CVT Unit
4. Remove the snap ring (1) from the CVT unit connector (A).
5. Press the CVT unit connector (A) into the transaxle case.
CAUTION:
Never damage the CVT unit connector.
NOTE:
Clean around the connector to prevent foreign materials from
entering into the transaxle case.
6. Remove the oil pan bolts, and then remove the oil pan and oil pan gasket.
7. Remove the magnets from the oil pan.
8. Remove the lock nut (1) and washer (2), and then remove the
instruction plate (3).
9. Remove the collar (4) from the instruction shaft (A).
CAUTION:
Never drop the collar.
10. Disconnect the connectors (A) and (B).
JPDIA0654ZZ
JPDIA0720ZZ
Front of vehicle
JPDIA0655ZZ
Clips
Front of vehicle
JPDIA0656ZZ
TM-442
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
CONTROL VALVE
11. Remove the oil strainer assembly bolts (A) and (B), and then
remove the oil strainer assembly (1).
12. Remove the bracket (1).
13. Remove the control valve bolts (A) and (B), and then remove the
control valve from the transaxle case.
CAUTION:
Never drop the control valve, ratio control valve and instruction
shaft.
14. Remove CVT unit connector (A) from the transaxle case inside.
15. Remove the lip seal (1) from the transaxle case.
Front of vehicle
JPDIA0657ZZ
Bolt
Front of vehicle
JPDIA0658ZZ
Front of vehicle
JPDIA0659ZZ
JPDIA0660ZZ
Front of vehicle
JPDIA0661ZZ
CONTROL VALVE
TM-443
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INSTALLATION
1. Install the lip seal (1) to the transaxle case.
2. Install the CVT unit connector (A) to the transaxle case.
CAUTION:
Connect the CVT unit connector with the stopper facing up,
and then press in until it clicks.
3. Press in the ratio control valve (B) in the (
) direction, and then
fix the linkage in the position shown with the linkage fixing pin
(A) from the back of control valve through the hole for fixing.
4. Check that one end of linkage engages with the step motor end
(C) and that the linkage is in the direction shown.
5. Install the control valve to the transaxle case.
CAUTION:
• Never drop the linkage fixing pin. If it is dropped, repeat
the installation procedure from step 3.
• Never pinch the harness into between the control valve
and the transaxle case.
Front of vehicle
JPDIA0661ZZ
JPDIA0660ZZ
JPDIA0663ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст