Nissan Altima L32. Instruction — part 854
PRECAUTIONS
INT-9
< PRECAUTION >
[COUPE]
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSION-
ER"
INFOID:0000000004205951
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004507229
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
Precautions
INFOID:0000000004205952
• After removing and installing any opening/closing parts, make sure to perform all adjustments for proper
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts which may
get in the way with cloth.
INT-10
< PRECAUTION >
[COUPE]
PRECAUTIONS
• When removing parts with a screw driver or other tool, protect parts by wrapping them with vinyl or tape.
• Keep removed parts protected with cloth.
• If a clip is deformed or damaged, replace it.
• If a non reuseable part is removed, replace it with a new one.
• Tighten bolts and nuts firmly to the specified torque.
• After re-assembly has been completed, make sure each part functions correctly.
• Remove stains in the following manner:
Water-Soluble stains
Oil stains
Dip a cloth in warm water, and squeeze tightly. After wip-
ing the stain, wipe with a soft dry cloth.
Dissolve a synthetic detergent in warm water (density of 2
to 3% or less), dip the cloth, then clean off the stain with
the cloth. Next, dip the cloth in fresh water, then squeeze
tightly. Clean off detergent completely, then wipe entire
area with a soft dry cloth.
Do not use any organic solvent, such as a thinner or benzine to remove stains
PREPARATION
INT-11
< PREPARATION >
[COUPE]
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000004205953
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000004205954
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Power tools
Loosening bolts, nuts and screws
SIIA0995E
PIIB1407E
INT-12
< ON-VEHICLE REPAIR >
[COUPE]
DOOR FINISHER
ON-VEHICLE REPAIR
DOOR FINISHER
Exploded View
INFOID:0000000004205955
Removal and Installation
INFOID:0000000004205956
FRONT DOOR FINISHER
Removal
1. Release the pawls at the rear edge and remove inside release handle escutcheon, then remove the
screw.
2. Lift power window and door lock/unlock switch finisher upward to remove, then disconnect the connec-
tors.
• Remove the front door finisher screw beneath power window and door lock/unlock switch finisher.
3. Place a suitable tool (A) under the rear corner of the armrest fin-
isher (1) and disengage the bottom plastic clips. Slide the tool up
to disengage the three metal clips.
CAUTION:
Do not pull on the armrest finisher.
1.
Power window switch finisher
2.
Front door finisher
3.
Step lamp
4.
Armrest finisher
5.
Inside release handle escutcheon
6.
Inside release handle
Clip
ALJIA0239ZZ
ALJIA0240ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст