Nissan Altima L32. Instruction — part 1567
DIAGNOSIS SYSTEM (BCM)
WT-11
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DIAGNOSIS SYSTEM (BCM)
CONSULT-III Function (BCM)
INFOID:0000000004205303
CONSULT-III DIAGNOSTIC MODES
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
DESCRIPTION
During driving, the tire pressure monitoring system receives the signal transmitted from the transmitter
installed in each wheel, and turns on the low tire pressure warning lamp when the tire pressure becomes low.
The control unit (BCM) for this system has pressure judgement and self-diagnosis functions.
FUNCTION
When the tire pressure monitoring system detects low inflation pressure or an internal malfunction, the low tire
pressure warning lamp in the combination meter comes on. The malfunction is indicated by the low tire pres-
sure warning lamp flashing.
CONSULT-III Application to Tire Pressure Monitoring System
× : Applicable
– : Not applicable
Data Monitor Mode
Diagnostic mode
Description
Work Support
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are re-
ceived from the BCM and received data is displayed.
Data Monitor
Displays BCM input/output data in real time.
Active Test
Operation of electrical loads can be checked by sending drive signal to them.
Self-Diagnostic Result
Displays BCM self-diagnosis results.
CAN Diagnostic Support Monitor
The result of transmit/receive diagnosis of CAN communication can be read.
ECU Identification
BCM part number can be read.
Configuration
Performs BCM configuration read/write functions.
ITEM
SELF-DIAGNOSTIC RESULTS
DATA MONITOR
Front - Left transmitter
×
×
Front - Right transmitter
×
×
Rear - Left transmitter
×
×
Rear - Right transmitter
×
×
Warning lamp
—
×
Vehicle speed
×
×
CAN Communication
×
×
MONITOR
CONDITION
SPECIFICATION
VHCL SPEED
Drive vehicle.
Vehicle speed (km/h or MPH)
AIR PRESS FL
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
• Drive vehicle for a few minutes.
Tire pressure (kPa or psi)
or
• Ignition switch ON and activation tool
is transmitting activation signals.
WT-12
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or the actual malfunction location may be different from that displayed on
CONSULT-III.
Self-Diagnosis (Without CONSULT-III)
INFOID:0000000004471324
SELF DIAGNOSTIC PROCEDURE (WITHOUT CONSULT-III)
1. Turn ignition switch ON.
2. Ground the tire pressure warning check connector to initiate self diagnosis.
3. Compare the flashing pattern with the flash code chart below.
NOTE:
The system is normal when the low tire pressure warning lamp flashes 5 times and continues repeating. Self-
diagnosis results are erased automatically by turning the ignition switch “OFF”.
ID REGST FL1
ID REGST FR1
ID REGST RR1
ID REGST RL1
Ignition switch ON
ID not registered: YET
ID registered: DONE
WARNING LAMP
Low tire pressure warning lamp on: ON
Low tire pressure warning lamp off: OFF
BUZZER
Buzzer in combination meter on: ON
Buzzer in combination meter off: OFF
MONITOR
CONDITION
SPECIFICATION
Flash Code
Malfunction part
Reference
page
15
16
17
18
Tire pressure dropped below specified value. Refer to
—
21
22
23
24
Transmitter no data (FL)
Transmitter no data (FR)
Transmitter no data (RR)
Transmitter no data (RL)
31
32
33
34
Transmitter checksum error (FL)
Transmitter checksum error (FR)
Transmitter checksum error (RR)
Transmitter checksum error (RL)
35
36
37
38
Transmitter pressure data error (FL)
Transmitter pressure data error (FR)
Transmitter pressure data error (RR)
Transmitter pressure data error (RL)
41
42
43
44
Transmitter function code error (FL)
Transmitter function code error (FR)
Transmitter function code error (RR)
Transmitter function code error (RL)
ALEIA0050GB
DIAGNOSIS SYSTEM (BCM)
WT-13
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
45
46
47
48
Transmitter battery voltage low (FL)
Transmitter battery voltage low (FR)
Transmitter battery voltage low (RR)
Transmitter battery voltage low (RL)
52
Vehicle speed signal
53
TPMS malfunction in BCM
Flash Code
Malfunction part
Reference
page
WT-14
< COMPONENT DIAGNOSIS >
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
COMPONENT DIAGNOSIS
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
INFOID:0000000004471325
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
INFOID:0000000004471326
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does DATA MONITOR ITEM display tire pressure as normal without any warning lamp?
YES
>> Inspection End.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000004205305
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.
CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connections.
Is tire pressure receiver connector damaged or loose?
YES
>> Repair or replace tire pressure receiver connector.
NO
>> Replace BCM, then GO TO 3. Refer to
BCS-96, "Removal and Installation"
3.
PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. Refer to
WT-6, "ID Registration Procedure"
Is there a tire that cannot register ID?
YES
>> Replace malfunctioning transmitter, then GO TO 5. Refer to
WT-68, "Removal and Installation"
NO
>> GO TO 4
4.
DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11
MPH).
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp?
YES
>> Inspection End.
DTC
CONSULT-III
DTC detecting condition
C1708
[NO - DATA] - FL
Data from FL transmitter cannot be received.
C1709
[NO - DATA] - FR
Data from FR transmitter cannot be received.
C1710
[NO - DATA] - RR
Data from RR transmitter cannot be received.
C1711
[NO - DATA] - RL
Data from RL transmitter cannot be received.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст