Nissan Altima L32. Instruction — part 1566
INSPECTION AND ADJUSTMENT
WT-7
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided "asleep" and must first be "woken up" using Transmitter
Activation Tool J-45295 before ID registration can be performed.
1. Connect CONSULT-III.
2. Select "ID REGIST" under BCM.
3. Adjust the tire pressures to the values shown in the table and drive the vehicle at 40 km/h (25 MPH) or
more for a few minutes.
4. After completing all ID registrations, press “END” to complete the procedure.
5. Inflate all tires to proper pressure. Refer to
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
250 (2.5, 36)
Front RH
230 (2.3, 33)
Rear RH
210 (2.1, 30)
Rear LH
190 (1.9, 27)
Activation tire position
CONSULT-III
Front LH
“YET”
↓
“DONE”
Front RH
Rear RH
Rear LH
WT-8
< FUNCTION DIAGNOSIS >
TPMS
FUNCTION DIAGNOSIS
TPMS
System Diagram
INFOID:0000000004205300
System Description
INFOID:0000000004205301
BODY CONTROL MODULE (BCM)
The BCM is shown with the instrument panel LH removed. The BCM
reads the air pressure signal received by the tire pressure receiver,
and controls the low tire pressure warning lamp as shown below. It
also has a self-diagnosis function to detect a system malfunction.
TRANSMITTER
A sensor-transmitter integrated with a valve is installed in each
wheel. It transmits a detected air pressure signal in the form of a
radio wave when the vehicle is moving. The radio signal is received
by the tire pressure receiver.
TIRE PRESSURE RECEIVER
ALEIA0004GB
Condition
Low tire pressure warning lamp
System normal
On for 1 second after ignition ON
Tire pressure less than 174.1 kPa (1.775
kg/cm
2
, 25.25 psi)
ON
Tire pressure monitoring system malfunc-
tion
After key ON, flashes once per sec-
ond for 1 minute, then stays ON
ALEIA0005ZZ
WEIA0137E
TPMS
WT-9
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
The tire pressure receiver (1) is located next to the steering column
assembly (2) and is shown with the lower instrument panel LH
removed. The tire pressure receiver receives the air pressure signal
transmitted by the transmitter in each wheel.
COMBINATION METER
The combination meter receives tire pressure status from the BCM
using CAN communication. When a low tire pressure condition is
sensed by the BCM, the low tire pressure warning lamp is activated.
TIRE PRESSURE WARNING CHECK CONNECTOR
The tire pressure warning check connector can be grounded in order
to initiate self-diagnosis without a CONSULT-III. Refer to
"Self-Diagnosis (Without CONSULT-III)"
. The tire pressure warning
check connector (1) is located behind the lower portion of the instru-
ment panel LH.
ALEIA0011ZZ
LEIA0055E
AWEIA0121ZZ
WT-10
< FUNCTION DIAGNOSIS >
TPMS
System Components
INFOID:0000000004205302
ALEIA0007ZZ
1.
Tire pressure receiver M70
2.
Tire pressure warning check connec-
tor M62
3.
Transmitters
4.
Combination meter M24
5.
BCM M16, M17, M18, M19
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст