Nissan Altima L32. Instruction — part 860
DOOR FINISHER
INT-33
< ON-VEHICLE REPAIR >
[SEDAN]
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
ON-VEHICLE REPAIR
DOOR FINISHER
Exploded View
INFOID:0000000004205974
ALJIA0001ZZ
INT-34
< ON-VEHICLE REPAIR >
[SEDAN]
DOOR FINISHER
Removal and Installation
INFOID:0000000004205975
FRONT DOOR FINISHER
Removal
1. Release the pawls and remove step lamp lens, then disconnect the connector.
2. Release the pawls at the rear edge and remove inside release handle escutcheon, then remove the
screw.
3. Release the clip at the front edge, then lift upward to release pawls and remove arm rest finisher.
4. Lift power window and door lock/unlock switch finisher upward to remove, then disconnect the connec-
tors.
• Remove the front door finisher screws beneath power window and door lock/unlock switch finisher.
5. Release the clips around outer edge, then remove front door finisher.
6. Disconnect inside release handle and lock knob cables from back of front door finisher.
7. Release the pawls and remove mirror cover.
REAR DOOR FINISHER
Removal
1. Release the pawls and remove the step lamp/reflector lens, then disconnect the connector (if equipped).
2. Release the pawls at the rear edge and remove inside release handle escutcheon, then remove the
screw.
3. Release the pawls and lift upward to remove arm rest finisher.
4. Lift power window switch finisher upward to remove, then disconnect the connector.
• Remove the rear door finisher screws beneath power window switch finisher.
5. Release the clips around outer edge, then remove rear door finisher.
6. Disconnect inside release handle and lock knob cables from the back of rear door finisher.
Installation
Installation is in the reverse order of removal.
1.
Mirror cover
2.
Front door finisher
3.
Step lamp lens
4.
Rear door finisher
5.
Step lamp/reflector lens (if equipped) 6.
Arm rest finisher
7.
Rear door power window switch fin-
isher
8.
Inside release handle
9.
Inside release handle escutcheon
10. Front door power window and door
lock/unlock switch finisher
A.
Screw
Clip C101
Pawl
Vehicle front
BODY SIDE TRIM
INT-35
< ON-VEHICLE REPAIR >
[SEDAN]
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000004205976
1.
Front pillar finisher
2.
Dash side lower finisher
3.
Front kicking plate
4.
Front sill cover
5.
Center pillar lower finisher
6.
Rear sill cover
7.
Rear kicking plate
8.
Rear body side welt
9.
Rear pillar finisher
ALJIA0002ZZ
INT-36
< ON-VEHICLE REPAIR >
[SEDAN]
BODY SIDE TRIM
Removal and Installation
INFOID:0000000004205977
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finishers.
REMOVAL
FRONT PILLAR FINISHER
1. Remove front body side welt.
CAUTION:
Insert a suitable clip removing tool wrapped with a shop
cloth inserted into the part shown by the arrow (between
the clip and the body side panel), then release the clip.
2. Release the clips, then remove front pillar finisher.
DASH SIDE LOWER FINISHER
1. Remove front kicking plate.
2. Release the clips, then remove dash side lower finisher.
FRONT KICKING PLATE
Release the clip and pawls, then remove front kicking plate.
FRONT BODY SIDE WELT
1. Remove front kicking plate.
2. Release welt from the body opening, then remove front body side welt.
CENTER PILLAR LOWER FINISHER
1. Remove front and rear body side welt.
2. Remove front and rear kicking plate.
3. Release the clips and pawls, then remove center pillar lower finisher.
CENTER PILLAR UPPER FINISHER
1. Remove screw cover, then remove the screw.
2. Remove front seat belt adjuster cover and shoulder anchor bolt. Refer to
.
3. Remove center pillar lower finisher.
4. Release the clips, then remove center pillar upper finisher.
REAR KICKING PLATE
Release the clip and pawl, then remove rear kicking plate.
REAR BODY SIDE WELT
1. Remove rear kicking plate.
2. Release the welt from the body opening, then remove rear body side welt.
REAR PILLAR FINISHER
1. Remove rear body side welt.
2. Remove screw cover, then remove the screw.
10. Screw cover
11. Center pillar upper finisher
12. Front seat belt adjuster cover
13. Front body side welt
A.
Screw
Clip C101
Pawl
Metal clip
Vehicle front
PIIB2768J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст