Nissan Altima L32. Instruction — part 269
P0128 THERMOSTAT FUNCTION
EC-197
< COMPONENT DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0128 THERMOSTAT FUNCTION
DTC Logic
INFOID:0000000004349246
DTC DETECTION LOGIC
NOTE:
If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303 or P0304, first perform the trouble
diagnosis for DTC P0300, P0301, P0302, P0303, P0304. Refer to
.
Engine coolant temperature has not risen enough to open the thermostat even though the engine has run long
enough.
This is due to a leak in the seal or the thermostat stuck open.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
TESTING CONDITION:
• For best results, perform at ambient temperature of –10
°C (14°F) or higher.
• For best results, perform at engine coolant temperature of –10
°C (14°F) to 52°C (126°F).
• Before performing the following procedure, do not fill with the fuel.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1. Turn A/C switch OFF.
2. Turn blower fan switch OFF.
3. Turn ignition switch ON.
4. Select “COOLAN TEMP/S” in “DATA MONITOR” mode with CONSULT-III.
5. Check the indication of “COOLAN TEMP/S”
If it is below 52
°C (126°F), go to following step.
If it is above 52
°C (126°F), cool down the engine to less than 52°C (126°F). Then go to next steps.
6. Start engine and drive vehicle for 10 consecutive minutes under the following conditions.
If “COOLAN TEMP/S” increases to more than 71
°C (160°F) within 10 minutes, turn ignition switch
OFF because the test result will be OK.
7. Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT-III” above.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004349247
1.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
EC-198, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace engine coolant temperature sensor.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0128
Thermostat function
The engine coolant temperature does not
reach to specified temperature even though
the engine has run long enough.
• Thermostat
• Leakage from sealing portion of thermostat
• Engine coolant temperature sensor
VHCL SPEED SE
More than 56 km/h (35 MPH)
EC-198
< COMPONENT DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
P0128 THERMOSTAT FUNCTION
2.
CHECK THERMOSTAT
CO-21, "Removal and Installation"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace thermostat.
Component Inspection
INFOID:0000000004455860
1.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect engine coolant temperature sensor harness connector.
3. Remove engine coolant temperature sensor.
4. Check resistance between engine coolant temperature sensor
terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace engine coolant temperature sensor.
Terminals
Condition
Resistance (k
Ω)
1 and 2
Temperature [
°C (°F)]
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
PBIB2005E
P0130 A/F SENSOR 1
EC-199
< COMPONENT DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0130 A/F SENSOR 1
Description
INFOID:0000000004349249
The air fuel ratio (A/F) sensor 1 is a planar one-cell limit current sen-
sor. The sensor element of the A/F sensor 1 is composed an elec-
trode layer, which transports ions. It has a heater in the element.
The sensor is capable of precise measurement = 1, but also in the
lean and rich range. Together with its control electronics, the sensor
outputs a clear, continuous signal throughout a wide range.
The exhaust gas components diffuse through the diffusion layer at
the sensor cell. An electrode layer is applied voltage, and this current
relative oxygen density in lean. Also this current relative hydrocar-
bon density in rich.
Therefore, the A/F sensor 1 is able to indicate air fuel ratio by this
electrode layer of current. In addition, a heater is integrated in the
sensor to ensure the required operating temperature of about 800
°C
(1,472
°F).
DTC Logic
INFOID:0000000004349250
DTC DETECTION LOGIC
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1
signal fluctuates according to fuel feedback control.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
With CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Let it idle for 2 minutes.
3. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO-1 >> With CONSULT-III: GO TO 3.
JMBIA0112GB
PBIB3354E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible Cause
P0130
Air fuel ratio (A/F) sensor 1
circuit
A)
The A/F signal computed by ECM from the A/F
sensor 1 signal is constantly in the range other
than approx. 2.2V.
• Harness or connectors
(The A/F sensor 1 circuit is open
or shorted.)
• A/F sensor 1
B)
The A/F signal computed by ECM from the A/F
sensor 1 signal is constantly approx. 2.2V.
EC-200
< COMPONENT DIAGNOSIS >
[QR25DE FOR CALIFORNIA]
P0130 A/F SENSOR 1
NO-2 >> Without CONSULT-III: GO TO 7.
3.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION
1. Select “A/F SEN1 (B1)” in “DATA MONITOR” mode with CONSULT-III.
2. Check “A/F SEN1 (B1)”indication.
Does the indication fluctuates around 2.2V?
YES
>> GO TO 4.
NO
>> Go to
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-I
1. Select “A/F SEN1 (B1) P1276” of “A/F SEN1” in “DTC WORK SUPPORT” mode with CONSULT-III.
2. Touch “START”.
3. When the following conditions are met, “TESTING” will be displayed on the CONSULT-III screen.
If “TESTING” is not displayed after 20 seconds, retry from step 2.
CAUTION:
Always drive vehicle at a safe speed.
Is “TESTING” displayed on CONSULT-III screen?
YES
>> GO TO 5.
NO
>> Check A/F sensor 1 function again. GO TO 3.
5.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-II
Release accelerator pedal fully.
NOTE:
Never apply brake during releasing the accelerator pedal.
Which does “TESTING” change to?
COMPLETED>>GO TO 6.
OUT OF CONDITION>>Retry DTC CONFIRMATION PROCEDURE. GO TO 4.
6.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B-III
Touch “SELF-DIAG RESULT”
Which is displayed on CONSULT-III screen?
YES
>> INSPECTION END
NO
>> Go to
7.
PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B
Perform Component Function Check. Refer to
EC-200, "Component Function Check"
NOTE:
Use component function check to check the overall function of the A/F sensor 1 circuit. During this check, a
1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Component Function Check
INFOID:0000000004349251
1.
PERFORM COMPONENT FUNCTION CHECK
With GST
1. Start engine and warm it up to normal operating temperature.
2. Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in the suitable gear position.
ENG SPEED
1,000 - 3,200 rpm
VHCL SPEED SE
More than 64 km/h (40 mph)
B/FUEL SCHDL
1.0 - 11.5 msec
Shift lever
D position (CVT)
5th position (M/T)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст