Nissan Altima L32. Instruction — part 1501
TM-348
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
P0868 SECONDARY PRESSURE DOWN
Check resistance between CVT unit terminal 3 and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
.
CVT unit terminal
Ground
Resistance (Approx.)
3
3.0 – 9.0
Ω
AWDIA0123ZZ
P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)
TM-349
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)
Description
INFOID:0000000004201938
When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diag-
nosis memory function stops, malfunction is detected.
NOTE:
Since “P1701 TCM-POWER SUPPLY” will be indicated when replacing TCM, perform diagnosis after erasing
“SELF-DIAG RESULTS”
DTC Logic
INFOID:0000000004201939
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Wait for at least 2 consecutive seconds.
3. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is “P1701 TCM-POWER SUPPLY” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000004201940
1.
CHECK TCM POWER SOURCE
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check voltage between TCM harness connector F16 terminal
46, 48, 45, 47 and 5, 42.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P1701
TCM-POWER SUPPLY
• When the power supply to the TCM is cut
OFF, for example because the battery is
removed, and the self-diagnosis memory
function stops.
• This is not a malfunction message (When-
ever shutting OFF a power supply to the
TCM, this message appears on the
screen).
Harness or connectors
(Battery or ignition switch and TCM circuit is
open or shorted.)
TCM harness connector
Condition
Voltage
(Approx.)
Connec-
tor
Terminal
F16
46
5, 42
Ignition switch ON
Battery
voltage
Ignition switch OFF
0 V
48
Ignition switch ON
Battery
voltage
Ignition switch OFF
0 V
45
Always
Battery
voltage
47
AWDIA0140ZZ
TM-350
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK TCM GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between TCM harness connector F16 terminal
5, 42 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TCM POWER CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between TCM harness connector F16 terminal
46, 48, 45, 47 and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 4.
4.
CHECK HARNESS BETWEEN TCM AND IPDM E/R AND BETWEEN TCM AND BATTERY (PART 1)
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector F10.
3. Check continuity between TCM harness connector F16 (A) ter-
minal 46, 48 and IPDM E/R harness connector F10 (B) terminal
58.
TCM harness connector
Ground
Continuity
Connector
Terminal
F16
5
Existed
42
AWDIA0141ZZ
TCM vehicle side har-
ness connector
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
F16
46
Ignition switch ON
Battery
voltage
Ignition switch OFF
0 V
48
Ignition switch ON
Battery
voltage
Ignition switch OFF
0 V
45
Always
Battery
voltage
47
AWDIA0142ZZ
TCM harness connector
IPDM E/R harness connector
Continuity
Connector
Terminal
Connector
Terminal
F16 (A)
46
F10 (B)
58
Existed
48
AWDIA0143ZZ
P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)
TM-351
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4. Disconnect fuse block J/B harness connector.
5. Check continuity between TCM harness connector F16 (A) ter-
minal 45, 47 and fuse block J/B harness connector E6 terminal
12P.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK HARNESS BETWEEN TCM AND IPDM E/R AND BETWEEN TCM AND BATTERY (PART 2)
Check continuity between TCM harness connector F16 terminal 45,
46, 47, 48 and ground.
Is the inspection result normal?
YES
>> Check the following.
• 10A fuse (No. 34, located in IPDM E/R)
• 10A fuse [No. 11, located in fuse block (J/B)]
• Ignition switch. Refer to
NO
>> Repair or replace damaged parts.
6.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
TCM harness connector
Fuse block J/B harness connec-
tor
Continuity
Connector
Terminal
Connector
Terminal
F16 (A)
45
E6 (B)
12P
Existed
47
AWDIA0144ZZ
TCM harness connector
Ground
Continuity
Connector
Terminal
F16
45
Not existed
46
47
48
JPDIA1000GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст