Nissan Altima L32. Instruction — part 1502

TM-352

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P1705 THROTTLE POSITION SENSOR

P1705 THROTTLE POSITION SENSOR

Description

INFOID:0000000004201941

Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle

position sensor etc. The actuator sends a signal to the ECM, and ECM sends the signal to TCM with CAN

communication.

DTC Logic

INFOID:0000000004201942

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT-III

1. Turn ignition switch ON.

2. Depress accelerator pedal fully and release it, then wait for 5 seconds.

3. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is “P1705 TP SEN/CIRC A/T” detected?

YES

>> Go to

TM-352, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000004201943

1.

CHECK DTC WITH ECM

With CONSULT-III

1. Turn ignition switch ON.

2. Perform “SELF-DIAG RESULTS” mode for “ENGINE”.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check DTC Detected Item. Refer to

EC-527, "DTC Index"

(for california),

EC-1015, "DTC Index"

(except for california).

2.

CHECK DTC WITH TCM

With CONSULT-III

Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is “P1705 TP SEN/CIRC A/T” detected?

YES

>> Replace TCM. Refer to

TM-430, "Exploded View"

.

NO

>> GO TO 3.

3.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?

YES

>> Replace TCM. Refer to

TM-430, "Exploded View"

.

NO

>> Repair or replace damaged parts.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P1705

TP SEN/CIRC A/T

TCM does not receive the proper accelera-
tor pedal position signals (input by CAN
communication) from ECM.

• ECM
• Harness or connectors

(CAN communication line is open or
shorted.)

P1722 ESTM VEHICLE SPEED SIGNAL

TM-353

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P1722 ESTM VEHICLE SPEED SIGNAL

Description

INFOID:0000000004201944

The vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) to TCM by CAN com-

munication line.

DTC Logic

INFOID:0000000004201945

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT-III

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Start engine and maintain the following conditions for at least 5 consecutive seconds.

Is “P1722 ESTM VEH SPD SIG” detected?

YES

>> Go to

TM-353, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000004201946

1.

CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

With CONSULT-III

Perform “SELF-DIAG RESULTS” mode for “ABS”.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check DTC detected item. Refer to

BRC-121, "DTC No. Index"

(TCS/ABS),

BRC-223, "DTC No.

Index"

(VDC/TCS/ABS).

2.

CHECK DTC WITH TCM

With CONSULT-III

Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is “P1722 ESTM VEH SPD SIG” detected?

YES

>> Replace TCM. Refer to

TM-430, "Exploded View"

.

NO

>> GO TO 3.

3.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P1722

ESTM VEH SPD SIG

• CAN communication with the ABS actua-

tor and the electric unit (control unit) is
malfunctioning.

• There is a great difference between the

vehicle speed signal from the ABS actua-
tor and the electric unit (control unit), and
the vehicle speed sensor signal.

• Harness or connectors

(Sensor circuit is open or shorted.)

• ABS actuator and electric unit (control

unit)

ACC PEDAL OPEN

: 1.0/8 or less

VEHICLE SPEED

: 30 km/h (19 MPH) or more

TM-354

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P1722 ESTM VEHICLE SPEED SIGNAL

Is the inspection result normal?

YES

>> Replace TCM. Refer to

TM-430, "Exploded View"

.

NO

>> Repair or replace damaged parts.

P1723 CVT SPEED SENSOR FUNCTION

TM-355

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P1723 CVT SPEED SENSOR FUNCTION

Description

INFOID:0000000004201947

The vehicle speed sensor CVT [output speed sensor (secondary speed sensor)] detects the revolution of

parking gear and generates a pulse signal. The pulse signal is sent to the TCM, which converts it into vehicle

speed.

The input speed sensor (primary speed sensor) detects the primary pulley revolution speed and sends a sig-

nal to the TCM.

DTC Logic

INFOID:0000000004201948

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT-III

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Start engine and maintain the following conditions for at least 5 consecutive seconds.

Is “P1723 CVT SPD SEN/FNCTN” detected?

YES

>> Go to

TM-355, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000004201949

1.

CHECK STEP MOTOR FUNCTION

Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Is “P1778 STEP MOTR/FNC” detected?

YES

>> Repair or replace damaged parts. Refer to

TM-364, "DTC Logic"

.

NO

>> GO TO 2.

2.

CHECK OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR) SYSTEM

Check output speed sensor (secondary speed sensor) system. Refer to

TM-318, "DTC Logic"

.

Is the inspection result normal?

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P1723

CVT SPD SEN/FNCTN

A rotation sensor error is detected because
the gear does not change in accordance
with the position of the stepping motor.

CAUTION:

One of the “P0720 VEH SPD SEN/CIR
AT”, the “P0715 INPUT SPD SEN/CIRC”
or the “P0725 ENGINE SPEED SIG“ is
displayed with the DTC at the same time.

• Harness or connectors

(Sensor circuit is open or shorted.)

• Output speed sensor (secondary speed

sensor)

• Input speed sensor (primary speed sen-

sor)

• Engine speed signal system

VEHICLE SPEED

: 10 km/h (6 MPH) or more

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

ENG SPEED

: 450 rpm or more

Driving location

: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.

Была ли эта страница вам полезна?
Да!Нет
8 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности