Nissan Altima L32. Instruction — part 1364
SPIRAL CABLE
SR-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2. Next, turn it counterclockwise (about 2.0 turns) then stop turning at the point when the alignment
arrows (B) are directly across from each other.
3. Rotate the spiral cable slightly so the locating pin (2) is positioned at the top.
NOTE:
A service part is installed in the neutral position with a stopper clip in place and should not be adjusted
after the stopper clip is removed.
2. Install the spiral cable in the reverse order of removal.
3. Align the locating hole (1) at the top of the steering wheel with the locating pin of spiral cable during instal-
lation.
CAUTION:
• The spiral cable may snap by steering operation if the cable is installed in an improper position.
• Do not turn the spiral cable quickly or beyond the limit number of turns. (This can cause the cable to
snap.)
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT
−III.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
SR-10
< ON-VEHICLE REPAIR >
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE
Removal and Installation
INFOID:0000000004205568
REMOVAL
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
• Always work from the side of air bag module. Do not work from the front of it.
• Always place air bag module with pad side facing upward.
• Do not use old bolts after removal; replace with new bolts.
• Do not cause impact to the air bag module by dropping etc. Replace the air bag module if it has been
dropped or sustained an impact.
1. Disconnect the negative and positive battery terminals, then wait at least three minutes.
2. Remove the glove box assembly.
IP-12, "Removal and Installation"
3. Disconnect both front passenger air bag module connectors (1).
Vehicle front.
NOTE:
The figure shows installed condition of the front passenger air
bag module. (Lower view of the module installed without glove
box in place.)
4. Remove front passenger air bag module bolt (A).
5. Remove the remaining instrument panel from the vehicle. Refer
IP-12, "Removal and Installation"
6. Remove the front passenger air bag module screws (A).
Vehicle front.
7. Rotate the front passenger air bag module and release the rear
side hooks (1) from the instrument panel.
8. Remove the front passenger air bag module from the instrument
panel.
INSTALLATION - ORIGINAL PASSENGER AIR BAG MODULE
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to damage the harness while installing.
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory by CONSULT
−III.
ALHIA0030ZZ
ALHIA0016GB
ALHIA0015ZZ
FRONT PASSENGER AIR BAG MODULE
SR-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
INSTALLATION - SERVICE REPLACEMENT PASSENGER AIR BAG MODULE
1. Install front passenger air bag module to the instrument panel assembly.
2. Install the instrument panel assembly. Refer to
IP-12, "Removal and Installation"
3. Connect the front passenger air bag module harness connector to yellow 4-pin service replacement con-
nector and fasten to mounting bracket.
Wiring Harness Modification
The front passenger air bag module originally installed in the vehicle uses direct-connect style harness con-
nectors. Service replacement passenger air bag modules use tab-locking style harness connectors. If the front
passenger air bag module is replaced, or if the direct-connect harness connectors are damaged, the vehicle
wiring harness must be modified to allow connection of the service replacement front passenger air bag mod-
ule.
NOTE:
The wiring harness modification is to be performed only if the vehicle is equipped with the original front pas-
senger air bag module which uses direct-connect harness connectors. If the front passenger air bag module is
to be replaced in a vehicle that has already had the service replacement front passenger air bag module
installed, the wiring harness modification is not required.
1. Locate the yellow and orange direct-connect front passenger air bag module harness connectors.
2. Use wire cutters to cut back both previously used direct-connect front passenger air bag module harness
connectors from the vehicle wiring harness approximately 50 mm (1.9 in) from the connectors.
3. Remove approximately 150 mm (5.9 in) of the vehicle harness covering from the cut end.
4. Slide a piece of dual-wall heat shrink tubing (provided in the pas-
senger air bag module service kit) onto each wire of the previ-
ously used vehicle wiring harness.
5. Fold each wire back and insert into the end of the heat shrink
tubing so that the end of the wire is approximately centered in
the heat shrink tubing.
6. Use a heat gun to shrink the heat shrink tubing and seal the
wire.
7. Use electrical tape to secure the modified circuits to the outside
of the wiring harness.
8. Locate the front passenger air bag module service replacement connector that is taped back to the main
harness. Unwrap the tape to access the yellow service replacement connector and remove the dust cover
from the connector.
9. Connect service connector to front passenger air bag module.
10. Clip to service connector clipping point.
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
LHIA0017E
WHIA0062E
SR-12
< ON-VEHICLE REPAIR >
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000004205569
Sedan Models
Coupe Models
Removal and Installation
INFOID:0000000004205570
REMOVAL
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
• Do not use air tools or electric tools for servicing.
• Always work from the side of air bag module. Do not work from the front of it.
• Always place the curtain air bag module with air bag deployment side facing upward.
AWHIA0097GB
1.
Side curtain air bag module connector 2.
Side curtain air bag module A.
Side curtain air bag module bolt
Vehicle front
AWHIA0015GB
1.
Side curtain air bag module
2.
Side curtain air bag module
inflator
A.
Side curtain air bag module bolt
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст