Nissan Altima L32. Instruction — part 1363
DRIVER AIR BAG MODULE
SR-5
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
ON-VEHICLE REPAIR
DRIVER AIR BAG MODULE
Exploded View
INFOID:0000000004205565
Removal and Installation
INFOID:0000000004205566
REMOVAL
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
• Always work from the side of air bag module. Do not work from the front of it.
• Always place air bag module with pad side facing upward.
• Do not use old bolts after removal; replace with new bolts.
• Do not cause impact to the air bag module by dropping etc. Replace the air bag module if it has been
dropped or sustained an impact.
1. Disconnect the negative and positive battery terminals, then wait at least three minutes.
2. Remove side lids, then remove the driver air bag module bolts (RH/LH).
3. Raise driver air bag module away from the steering wheel, then disconnect the steering switches.
4. Disconnect the driver air bag module connectors, then remove driver air bag module from steering wheel.
• For installing/removing direct-connect SRS connectors, refer
SRC-9, "Direct-connect SRS Component Connectors"
.
1.
Steering switch connector
2.
Steering switch ground connector
3.
Steering switches
4.
Driver air bag module
5.
Driver air bag module connectors
6.
Side lid (RH/LH)
A.
Steering switch screw
B.
Driver air bag module bolt (RH/LH)
AWHIA0011GB
PHIA0953J
SR-6
< ON-VEHICLE REPAIR >
DRIVER AIR BAG MODULE
5. Disconnect the steering switch ground connector (1), then
release the harness (2) from the clips.
6. Remove the steering switch screws (RH/LH) (A), then remove
the steering switches from driver air bag module.
INSTALLATION
1. Attach steering switches (RH/LH) to driver air bag module.
2. Place the driver air bag module near the steering wheel and
attach connectors (A).
3. Lift the driver air bag module while rotating counterclockwise
into position over steering wheel.
ALHIA0021ZZ
ALHIA0096ZZ
DRIVER AIR BAG MODULE
SR-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
4. Pulling down on the steering switch harness, install the air bag
module into the steering wheel.
• Make sure that the steering switch harness is routed below the
center of the air bag module inflator (1) as shown (B), and is
not routed so it is pinched between the driver air bag module
inflator (1) and steering column shaft threads as shown (A).
CAUTION:
Make sure the steering switch harness is correctly routed
below the center of the driver air bag module inflator (1) as
shown (B), and NOT incorrectly routed across the driver air
bag module inflator as shown (A).
5. Install the remaining components in the reverse order of removal.
CAUTION:
• Be careful not to damage or pinch the harness while installing.
• Tighten the driver air bag module bolts after centering the holes between the driver air bag mod-
ule and the steering wheel horn contact bracket. If the holes are misaligned, the bolt threads may
become damaged and the module will not install securely.
• After the work is completed, make sure no system malfunction is detected by air bag warning
lamp.
• In case a malfunction is detected by the air bag warning lamp, reset by the self-diagnosis func-
tion and delete the memory by CONSULT–III.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair mal-
functions. Refer to
ALHIA0102ZZ
SR-8
< ON-VEHICLE REPAIR >
SPIRAL CABLE
SPIRAL CABLE
Removal and Installation
INFOID:0000000004205567
REMOVAL
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
• Do not use air tools or electric tools for servicing.
• Do not disassemble the spiral cable.
• Do not allow oil, grease, detergent or water to come in contact with the spiral cable.
• Do not cause impact to the spiral cable by dropping etc. Replace the spiral cable if it has been
dropped or sustained an impact.
• With the steering linkage disconnected, the cable may snap by turning the steering wheel beyond
the limited number of turns. The spiral cable can be turned counterclockwise about 2.0 turns from
the neutral position.
1. Disconnect the negative and positive battery terminals, then wait at least three minutes.
2. Remove the steering wheel. Refer to
ST-13, "Removal and Installation"
3. Remove the column cover. Refer to
IP-12, "Removal and Installation"
4. Disconnect the harness connectors (2) from spiral cable (1).
5. Rotate the spiral cable slightly so the locating pin (2) is posi-
tioned at the top.
• Locating hole (1)
• Alignment arrows (B)
6. Remove the screws (A), then remove spiral cable from the
steering column.
CAUTION:
Do not turn the spiral cable quickly or beyond the limit
number of turns (approximately 2.0 turns from the neutral
position), this may cause the cable to snap.
7. Remove the steering angle sensor. Refer to
INSTALLATION
1. Set the spiral cable neutral position.
1. Slowly turn the spiral cable clockwise to the end position.
ALHIA0013ZZ
ALHIA0014ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст