Nissan Altima L32. Instruction — part 195
COOLING FAN
CO-17
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
COOLING FAN
Removal and Installation
INFOID:0000000004205446
REMOVAL
1. Drain engine coolant from the radiator. Refer to
CO-12, "Changing Engine Coolant"
CAUTION:
Perform when engine is cold.
2. Remove air cleaner duct assembly. Refer to
EM-25, "Removal and Installation"
.
3. Disconnect radiator upper hose.
4. Disconnect fan motor connectors.
5. Remove radiator cooling fan assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation refill engine coolant and check for leaks. Refer to
CO-12, "Changing Engine Coolant"
and
.
CAUTION:
Do not spill coolant in engine compartment. Use a shop cloth to absorb coolant.
• Cooling fan is controlled by ECM. For details, refer to
1.
Fan blade
2.
Fan shroud and motor assembly
AWBIA0006GB
CO-18
< ON-VEHICLE REPAIR >
[QR25DE]
COOLING FAN
Disassembly and Assembly of Cooling Fan
INFOID:0000000004498335
DISASSEMBLY
1. Remove fan blade nut.
2. Remove fan blade from fan motor.
3. Remove fan motor bolts and remove fan motor from fan shroud.
ASSEMBLY
Assembly is in the reverse order of disassembly.
AWBIA0739GB
1. Fan blade
2. Fan shroud
3. Fan motor
WATER PUMP
CO-19
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
WATER PUMP
Removal and Installation
INFOID:0000000004205448
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
CAUTION:
• When removing water pump assembly, be careful not to get coolant on drive belt.
• Water pump cannot be disassembled and should be replaced as a unit.
• After installing water pump, connect hose and clamp securely, then check for leaks using radiator
cap tester.
REMOVAL
1. Drain engine coolant from the radiator. Refer to
CO-12, "Changing Engine Coolant"
CAUTION:
Perform when the engine is cold.
2. Remove drive belt. Refer to
EM-16, "Removal and Installation"
.
3. Remove engine cover using power tools.
4. Remove generator. Refer to
CHG-27, "Removal and Installation"
.
5. Remove RH wheel and tire assembly. Refer to
6. Remove fender protector RH. Refer to
EXT-19, "Removal and Installation"
(Coupe models) or
(Sedan models).
7. Remove engine ground strap.
8. Remove the water pump.
CAUTION:
• Handle the water pump vane so that it does not contact any other parts.
• Water pump cannot be disassembled and should be replaced as an assembly.
NOTE:
If it is necessary to remove the water pipe, the exhaust manifold and three way catalyst assembly must be
removed. Refer to
EM-30, "Removal and Installation"
INSPECTION AFTER REMOVAL
AWBIA0004GB
1.
Water pump
2.
Gaskets
3.
Water pump housing
4.
Water pipe
5.
O-ring
CO-20
< ON-VEHICLE REPAIR >
[QR25DE]
WATER PUMP
• Visually check that there is no significant dirt or rusting on the
water pump body and vane.
• Check that there is no looseness in the vane shaft, and that it turns
smoothly when rotated by hand.
• If the water pump does not perform properly, replace the water
pump assembly.
INSTALLATION
Installation is in the reverse order of removal.
• When inserting water pipe end to cylinder block, apply a neutral detergent to O-ring. Then insert it immedi-
ately.
INSPECTION AFTER INSTALLATION
• After installation refill engine coolant and check for leaks. Refer to
CO-12, "Changing Engine Coolant"
and
.
KBIA0155E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст