Nissan Altima L32. Instruction — part 196
THERMOSTAT AND THERMOSTAT HOUSING
CO-21
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
THERMOSTAT AND THERMOSTAT HOUSING
Removal and Installation
INFOID:0000000004205449
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
REMOVAL
CAUTION:
Perform when the engine is cold.
1. Drain engine coolant from the radiator. Refer to
CO-12, "Changing Engine Coolant"
2. Remove the air duct. Refer to
EM-25, "Removal and Installation"
.
3. Remove radiator lower hose from the engine coolant inlet side.
4. Remove engine coolant inlet and thermostat.
INSPECTION AFTER REMOVAL
1.
Thermostat 2.
O-ring
3.
Engine
coolant
inlet
4.
Water control valve
5.
Gasket
6.
Engine coolant outlet
7.
Copper washer
8.
Engine coolant temperature sensor
9.
Heater pipe
A. To electric throttle control
B. To oil cooler
C. To heater
D. To heater
E. To electric throttle control
F.
To oil cooler
Engine front
AWBIA0005GB
CO-22
< ON-VEHICLE REPAIR >
[QR25DE]
THERMOSTAT AND THERMOSTAT HOUSING
• Place a thread so that it is caught in the valves of the thermostat.
Immerse fully in a container filled with water. Heat while stirring.
• The valve opening temperature is the temperature at which the
valve opens and the falls from the thread.
• Continue heating. Check the full-open lift amount.
NOTE:
The full-open lift amount standard temperature for the thermostat is
the reference value.
• After checking the full-open lift amount, lower the water tempera-
ture and check the valve closing temperature.
INSTALLATION
Installation is in the reverse order of removal.
• Install the engine coolant temperature sensor.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products
• Install the thermostat with the whole circumference of the flange
part fitting securely inside the rubber ring.
• Install the thermostat with the jiggle valve facing upwards. The
position deviation may be within the range of
±10°.
• If necessary, to install the heater pipe, first apply a mild detergent
to the O-ring and then quickly insert the pipe into the housing.
SLC252B
Thermostat Standard
Values
Valve opening temperature
80.5 – 83.5
°C (177 – 182°F)
Full-open lift amount
More than 8 mm / 95
°C (0.315 in / 203°F)
Valve closing temperature
77
°C (171°F) or higher
PBIC0157E
WATER CONTROL VALVE
CO-23
< ON-VEHICLE REPAIR >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
WATER CONTROL VALVE
Removal and Installation
INFOID:0000000004205450
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
REMOVAL
CAUTION:
Perform when the engine cold.
1. Drain engine coolant from the radiator. Refer to
CO-12, "Changing Engine Coolant"
2. Remove the engine room cover using power tool.
3. Remove the air cleaner and air duct assembly. Refer to
EM-25, "Removal and Installation"
4. Remove the upper radiator hose, heater pipe, electric throttle control actuator inlet hose, and heater hose.
5. Remove the engine coolant outlet.
6. Remove the water control valve.
INSPECTION AFTER REMOVAL
1.
Thermostat
2.
O-ring
3.
Engine coolant inlet
4.
Water control valve
5.
Gasket
6.
Engine coolant outlet
7.
Copper washer
8.
Engine coolant temperature sensor
9.
Heater pipe
A. To electric throttle control
B. To oil cooler
C. To heater
D. To heater
E. To electric throttle control
F.
To oil cooler
Engine front
AWBIA0005GB
CO-24
< ON-VEHICLE REPAIR >
[QR25DE]
WATER CONTROL VALVE
• Place a thread so that it is caught in the valve of the water control
valve. Immerse fully in a container filled with water. Heat while stir-
ring.
• The valve opening temperature is the temperature at which the
valve opens and the falls from the thread.
• Continue heating. Check the full-open lift amount.
NOTE:
The full-open lift amount standard temperature for the water con-
trol valve is the reference value.
• After checking the full-open lift amount, lower the water tempera-
ture and check the valve closing temperature.
Standard values
INSTALLATION
Installation is in the reverse order of removal.
• Install the engine coolant temperature sensor.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products
• Install the water control valve with the whole circumference of the flange part fitting securely inside the rub-
ber ring.
• Install the water control valve with the up-mark facing up and the frame center part facing upwards. The
position deviation may be within the range of
±10°.
SLC252B
Water Control Valve
Standard Value
Valve opening temperature
93.5
° - 96.5°C (200° - 206°F)
Full-open lift amount
More than 8 mm / 108
°C (0.315 in / 226° F)
Valve closing temperature
90
°C (194° F) or higher
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст