Nissan Altima L32. Instruction — part 1222
SEC-38
< COMPONENT DIAGNOSIS >
[COUPE]
B2013 ID DISCORD, IMMU-STRG
B2013 ID DISCORD, IMMU-STRG
Description
INFOID:0000000004206023
BCM performs the ID verification with the steering lock unit and releases the steering lock if both BCM and
steering lock unit ID are same. BCM starts the communication with the steering lock unit when Intelligent Key
is carried into the passenger compartment and the push-button ignition switch is pressed.
DTC Logic
INFOID:0000000004206024
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Lock steering.
2. Press the push-button ignition switch
3. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206025
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all Intelligent Keys.
For initialization and registration of Intelligent Key. Refer to “CONSULT-III Operation Instruction”.
Can the system be initialized and can steering lock be released with re-registered Intelligent Key?
YES
>> Steering lock unit was unregistered.
NO
>> Replace steering wheel lock unit.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2013
ID DISCORD, IMMU-
STRG
The ID verification results between BCM and steer-
ing control unit are NG. The registration is neces-
sary.
• Steering wheel lock unit
B2014 CHAIN OF STRG-IMMU
SEC-39
< COMPONENT DIAGNOSIS >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2014 CHAIN OF STRG-IMMU
Description
INFOID:0000000004206026
BCM performs the ID verification with the steering lock unit to release the steering. BCM starts the communi-
cation with the steering lock unit when Intelligent Key is carried into the passenger compartment and the push-
button ignition switch is pressed.
DTC Logic
INFOID:0000000004206027
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Lock steering.
2. Press the push-button ignition switch.
3. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206028
1.
CHECK STEERING LOCK UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect steering lock unit harness connector.
3. Check voltage between steering lock unit harness connector
and ground while turning ignition switch from OFF to ACC.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> GO TO 2
2.
CHECK STEERING LOCK UNIT POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2014
CHAIN OF STRG-
IMMU
Inactive communication between steering
control unit and BCM
• Harness or connectors
(steering lock unit circuit is open or short-
ed)
• Steering lock unit
• BCM
Steering lock unit
Ground
Ignition switch
position
Voltage [V]
Connector
Terminal
M32
7
Ground
OFF
→ ACC
Battery voltage
OFF or ON
0
ALKIA1348ZZ
SEC-40
< COMPONENT DIAGNOSIS >
[COUPE]
B2014 CHAIN OF STRG-IMMU
3. Check continuity between steering lock unit harness connector
M32 (A) terminal 7 and BCM harness connector M19 (B) termi-
nal 94.
4. Check continuity between steering lock unit harness connector
M32 (A) terminal 7 and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair harness or connector.
3.
CHECK STEERING LOCK UNIT GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between steering lock unit and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair harness or connector.
4.
CHECK STEERING LOCK UNIT COMMUNICATION SIGNAL
1. Connect steering lock unit harness connector.
2. Using an oscilloscope, read voltage signal between steering
lock unit harness connector and ground.
Steering lock unit
BCM
Continuity
Connector
Terminal
connector
Terminal
A: M32
7
B: M19
94
Yes
Steering lock unit
Ground
Continuity
Connector
Terminal
A: M32
7
Ground
No
ALKIA0433ZZ
Steering lock unit
Ground
Continuity
Connector
Terminal
M32
5
Ground
Yes
6
ALKIA0434ZZ
ALKIA0435ZZ
B2014 CHAIN OF STRG-IMMU
SEC-41
< COMPONENT DIAGNOSIS >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> Replace steering lock unit.
NO
>> GO TO 5
5.
CHECK STEERING LOCK UNIT COMMUNICATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check continuity between BCM harness connector M19 (A) ter-
minal 99 and steering lock unit harness connector M32 (B) ter-
minal 2.
4. Check continuity between BCM harness connector M19 (A) ter-
minal 99 and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair harness or connector.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> Inspection End.
Steering lock unit
Ground
Steering lock unit condi-
tion
Value
Connector
Terminal
M32
2
Ground
Lock
Battery voltage
Lock or unlock
For 15 seconds after un-
lock
Battery voltage
15 seconds or later after
unlock.
0 V
Steering is locked
: Opening the door when ignition switch is ON to OFF.
Steering is unlocked
: Ignition switch is OFF to ACC.
JMKIA0066GB
BCM
Steering lock unit
Continuity
Connector
Terminal
connector
Terminal
A: M19
99
B: M32
2
Yes
BCM
Ground
Continuity
Connector
Terminal
A: M19
99
Ground
No
ALKIA0436ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст