Nissan Altima L32. Instruction — part 863
TRUNK ROOM TRIM & TRUNK LID FINISHER
INT-45
< ON-VEHICLE REPAIR >
[SEDAN]
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
TRUNK ROOM TRIM & TRUNK LID FINISHER
Exploded View
INFOID:0000000004205984
TRUNK ROOM TRIM
1.
Trunk lid finisher
2.
Trunk lid rubber bumper
3.
Trunk net rear
4.
Trunk rear finisher
5.
Trunk side finisher (RH)
6.
Trunk floor carpet
7.
Spare tire cover
8.
Trunk floor board (LH)
9.
Trunk side finisher (LH)
10. Trunk net side
A.
Clip C205
B.
Clip - hook type
Clip
Vehicle front
ALJIA0007ZZ
INT-46
< ON-VEHICLE REPAIR >
[SEDAN]
TRUNK ROOM TRIM & TRUNK LID FINISHER
Removal and Installation
INFOID:0000000004205985
REMOVAL
TRUNK ROOM TRIM
1. Release the latch, then position rear seatback (RH/LH) to the folded down position.
2. Release the clips, then remove trunk floor carpet.
3. Remove trunk net rear and trunk net side (if installed).
4. Release the clips, then remove trunk rear finisher.
5. Release the clips, then remove trunk side finisher (RH/LH).
6. Remove spare tire cover and trunk floor board (LH).
7. Remove the trunk lid rubber bumper (RH/LH), then release the clips and remove trunk lid finisher.
INSTALLATION
Installation is in the reverse order of removal.
IP-1
BODY INTERIOR
C
D
E
F
G
H
I
K
L
M
SECTION
IP
A
B
IP
N
O
P
CONTENTS
INSTRUMENT PANEL
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Supplemental Restraint System (SRS) "AIR B
AG" and "SEAT BELT PRE-TENSIONER" . . ....
Necessary for Steering Wheel Rotation After Bat-
tery Disconnect . . . . . . . . . . . . . .....
Precaution . . . . . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ..
Commercial Service Tools . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ...
Work Flow . . . . . . . . . . . . . . . . .
Inspection Procedure . . . . . . . . . . . ....
Diagnostic Worksheet . . . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . .
INSTRUMENT PANEL ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . ..
CENTER CONSOLE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . . .
IP-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER"
INFOID:0000000004205584
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004499025
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
Precaution
INFOID:0000000004205585
• Disconnect both battery cables in advance.
• Disconnect air bag system line in advance.
• Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
• Be careful not to scratch pad and other parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст