Nissan Altima L32. Instruction — part 790
GW-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000004204543
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000004204544
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Suction lifter
Holding the door glass
SIIA0995E
PIIB1805J
WINDSHIELD GLASS
GW-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
ON-VEHICLE REPAIR
WINDSHIELD GLASS
Components
INFOID:0000000004204545
Removal and Installation
INFOID:0000000004204546
REMOVAL
1. Partially remove the headlining (front edge). For Sedan Refer to
INT-42, "Removal and Installation"
.
For Coupe Refer to
INT-20, "Removal and Installation"
2. Remove the front wiper arms. For Sedan Refer to
INT-42, "Removal and Installation"
. For Coupe Refer to
ALKIA1449GB
1.
Windshield glass
2.
Spacer
3.
Mirror base
4.
Adhesive
5.
Roof panel
6.
Front pillar outer panel
7.
Cowl top center
8.
Primer
E.
7(0.28)
F.
12 (0.47)
G.
7.5 (0.30)
H.
16 (0.63)
I. 25
(0.98)
J.
12.5
(0.49)
GW-12
< ON-VEHICLE REPAIR >
WINDSHIELD GLASS
3. Remove roof side molding. For Sedan Refer to
EXT-45, "Removal and Installation"
. For Coupe Refer to
EXT-22, "Removal and Installation"
4. Apply a protective tape around the windshield glass to protect the painted surface from damage.
• After removing moldings, remove glass using piano wire or power cutting tool (A) and an inflatable pump bag
(B).
• If the windshield glass is to be reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:
• Be careful not to scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
• When the windshield glass is to be reused, do not use a cutting knife or power cutting tool.
INSTALLATION
Installation is in the reverse order of removal.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions furnished
with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperature and lower humidity.
Inspection
INFOID:0000000004204547
Repairing water Leaks for Windshield
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
PIIB5779E
REAR WINDOW GLASS
GW-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR WINDOW GLASS
Components - Sedan
INFOID:0000000004204548
1.
Rear window glass
2.
Spacer
3.
Adhesive
4.
Roof panel outer
5.
Rear window molding
6.
Body side outer
7.
Parcel shelf
8.
Primer
D.
7 (0.28)
E.
12 (0.47)
F.
12.5 (0.49)
G. 16 (0.63)
ALKIA0102ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст