Nissan Altima L32. Instruction — part 1229
SEC-66
< COMPONENT DIAGNOSIS >
[COUPE]
B2190, P1610 NATS ANTENNA AMP
Is the inspection result normal?
YES
>> GO TO 8
NO
>> Repair harness or connector.
7.
CHECK KEY SLOT GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect key slot harness connector.
3. Check continuity between key slot harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 8
NO
>> Repair harness or connector.
8.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> Inspection End.
Key slot
Ground
Continuity
Connector
Terminal
M40
7
Ground
Yes
ALKIA0344ZZ
B2191, P1615 DIFFERENCE OF KEY
SEC-67
< COMPONENT DIAGNOSIS >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2191, P1615 DIFFERENCE OF KEY
Description
INFOID:0000000004206014
Performs ID verification through BCM and Intelligent Key when push-button ignition switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ID of Intelligent Key is used.
DTC Logic
INFOID:0000000004206015
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206016
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all Intelligent Keys.
For initialization and registration of Intelligent Key. Refer to CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered Intelligent Key?
YES
>> Intelligent Key was unregistered.
NO
>> BCM is malfunctioning.
• Replace BCM. Refer to
BCS-96, "Removal and Installation"
.
• Perform initialization again.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2191
DIFFERENCE OF
KEY
The ID verification results between BCM and Intel-
ligent Key are NG. The registration is necessary.
• Intelligent Key
P1615
SEC-68
< COMPONENT DIAGNOSIS >
[COUPE]
B2192, P1611 ID DISCORD, IMMU-ECM
B2192, P1611 ID DISCORD, IMMU-ECM
Description
INFOID:0000000004206017
BCM performs the ID verification with ECM that allows the engine to start. Start the engine if the ID is OK.
ECM prevents the engine from starting if the ID is not registered. BCM starts the communication with ECM if
ignition switch is turned ON.
DTC Logic
INFOID:0000000004206018
DTC DETECTION LOGIC
NOTE:
• If DTC B2192 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2192 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions.
-
CVT selector lever is in the P or N position
-
Do not depress the brake pedal
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206019
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all Intelligent Keys.
For initialization and registration of Intelligent Key. Refer to CONSULT-III Operation Instruction.
Can the system be initialized and can the engine be started with re-registered Intelligent Key?
YES
>> ID was unregistered.
NO
>> BCM is malfunctioning.
• Replace BCM. Refer to
BCS-96, "Removal and Installation"
.
• Perform initialization again.
• Replace ECM.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2192
ID DISCORD, IMMU-
ECM
The ID verification results between BCM and ECM
are NG. The registration is necessary.
• BCM
• ECM
P1611
B2193, P1612 CHAIN OF ECM-IMMU
SEC-69
< COMPONENT DIAGNOSIS >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2193, P1612 CHAIN OF ECM-IMMU
Description
INFOID:0000000004206020
BCM performs the ID verification with ECM that allows the engine to start. Start the engine if the ID is OK.
ECM prevents the engine from starting if the ID is not registered. BCM starts the communication with ECM if
ignition switch is turned ON.
DTC Logic
INFOID:0000000004206021
DTC DETECTION LOGIC
NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions.
-
CVT selector lever is in the P or N position.
-
Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206022
1.
REPLACE BCM
1. Replace BCM. Refer to
BCS-96, "Removal and Installation"
.
2. Perform initialization with CONSULT-III.
For initialization, refer to CONSULT-III Operation Instruction”.
Does the engine start?
YES
>> BCM is malfunctioning.
• Replace BCM. Refer to
BCS-96, "Removal and Installation"
.
• Perform initialization again.
NO
>> ECM is malfunctioning.
• Replace ECM.
• Perform ECM re-communicating function.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2193
CHAIN OF ECM-
IMMU
Inactive communication between ECM and BCM
• Harness or connectors
(The CAN communication line is
open or shorted)
• BCM
• ECM
P1612
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст