Nissan Altima L32. Instruction — part 1230
SEC-70
< COMPONENT DIAGNOSIS >
[COUPE]
B2555 STOP LAMP
B2555 STOP LAMP
Description
INFOID:0000000004206029
BCM detects the stop lamp status and confirms the stop lamp switch ON/OFF status. BCM confirms the
engine start condition according to the stop lamp switch ON/OFF status.
DTC Logic
INFOID:0000000004206030
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Depress the brake pedal and wait for at least 1 second.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206031
1.
CHECK STOP LAMP SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Stop lamp switch is OK.
NO
>> GO TO 2
2.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1. Disconnect stop lamp switch harness connector.
2. Check voltage between stop lamp harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Check harness for open or short between stop lamp
switch and fuse.
DTC No.
Trouble diagno-
sis name
DTC detecting condition
Possible cause
B2555
STOP LAMP
BCM makes a comparison between the
upper voltage and lower voltage of stop
lamp switch. It judges from their values to
detect the malfunctioning circuit.
• Harness or connectors
(stop lamp switch circuit is open or shorted)
• Stop lamp switch
• Fuse
BCM
Ground
Stop lamp
switch position
Voltage [V]
Connector
Terminal
M18
26
Ground
Depressed
Battery volt-
age
Released
0
ALKIA0437ZZ
Stop lamp switch
Ground
Voltage [V]
Connector
Terminal
E38
1
Ground
Battery voltage
ALKIA0438ZZ
B2555 STOP LAMP
SEC-71
< COMPONENT DIAGNOSIS >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
3.
CHECK STOP LAMP SWITCH CIRCUIT
1. Check continuity between stop lamp switch harness connector
E38 (A) terminal 2 and BCM harness connector M18 (B) termi-
nal 26.
2. Check continuity between stop lamp switch harness connector
E38 (A) terminal 2 and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair harness or connector.
4.
CHECK STOP LAMP SWITCH
SEC-71, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace stop lamp switch.
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> Inspection End.
Component Inspection
INFOID:0000000004206032
1.
CHECK STOP LAMP SWITCH
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check continuity between stop lamp switch terminals under the
following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace stop lamp switch.
Stop lamp switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
A: E38
2
B: M18
26
Yes
Stop lamp switch
Ground
Continuity
Connector
Terminal
A: E38
2
Ground
No
ALKIA0439ZZ
Stop lamp switch
Condition
Continuity
Terminal
1
2
Brake pedal
Not depressed
No
Depressed
Yes
ALKIA0440ZZ
SEC-72
< COMPONENT DIAGNOSIS >
[COUPE]
B2556 PUSH-BUTTON IGNITION SWITCH
B2556 PUSH-BUTTON IGNITION SWITCH
Description
INFOID:0000000004206033
The switch that changes the power supply position. BCM maintains the power supply position status. BCM
changes the power supply position with the operation of the push-button ignition switch.
DTC Logic
INFOID:0000000004206034
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for at least 100 seconds.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206035
1.
CHECK PUSH-BUTTON IGNITION SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch harness connector.
3. Check voltage between push-button ignition switch harness con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> GO TO 4
2.
CHECK PUSH-BUTTON IGNITION SWITCH
SEC-73, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Replace push-button ignition switch. Refer to
SEC-208, "Removal and Installation"
.
3.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> Inspection End.
4.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT FOR SHORT
1. Disconnect BCM harness connector and IPDM E/R harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2556
PUSH-BUTTON IG-
NITION SWITCH
BCM detects the push-button ignition
switch stuck to ON for 100 seconds or
more
• Harness or connectors
(Push-button ignition switch circuit is shorted.)
• Push-button ignition switch
Push-button ignition switch
Ground
Voltage [V]
Connector
Terminal
M38
4
Ground
Battery voltage
ALKIA1350ZZ
B2556 PUSH-BUTTON IGNITION SWITCH
SEC-73
< COMPONENT DIAGNOSIS >
[COUPE]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
2. Check continuity between push-button ignition switch harness
connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-96, "Removal and Installa-
.
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000004206036
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch harness connector.
3. Check continuity between push-button ignition switch terminals
under the following conditions.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace push-button ignition switch. Refer to
SEC-208, "Removal and Installation"
.
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M38
4
Ground
No
ALKIA0442ZZ
ALKIA0443ZZ
Push-button ignition switch
Condition
Continuity
Terminal
1
4
Pressed
Yes
Not pressed
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст