Nissan Altima L32. Instruction — part 1274
SEC-246
< COMPONENT DIAGNOSIS >
[SEDAN WITH INTELLIGENT KEY]
B210A STEERING LOCK CONDITION SWITCH
YES
>> GO TO 11
NO
>> Repair harness or connector.
9.
CHECK IPDM E/R OUTPUT SIGNAL
1. Connect IPDM E/R harness connector.
2. Disconnect BCM harness connector.
3. Check voltage between electronic steering column lock harness
connector and ground.
Is the inspection result normal?
YES
>> Replace electronic steering column lock.
NO
>> GO TO 10
10.
CHECK ELECTRONIC STEERING COLUMN LOCK CIRCUIT-II
1. Check continuity between electronic steering column lock har-
ness connector M32 (A) terminal 8 and IPDM E/R harness con-
nector E18 (B) terminal 33.
2. Check continuity between electronic steering column lock har-
ness connector and ground.
Is the inspection result normal?
YES
>> GO TO 11
NO
>> Repair harness or connector.
11.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> Inspection End.
Electronic steering column lock
Ground
Voltage [V]
Connector
Terminal
M32
8
Ground
Battery voltage
ALKIA0457ZZ
Electronic steering column lock
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
A: M32
8
B: E18
33
Yes
Electronic steering column lock
Ground
Continuity
Connector
Terminal
A: M32
8
Ground
No
ALKIA0459ZZ
B210B STARTER CONTROL RELAY
SEC-247
< COMPONENT DIAGNOSIS >
[SEDAN WITH INTELLIGENT KEY]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210B STARTER CONTROL RELAY
Description
INFOID:0000000004206294
Starter control relay, integrated in IPDM E/R, permits the starter relay operation when in N or P position and
the steering is locked or unlocked. It is installed in parallel with the starter relay.
DTC Logic
INFOID:0000000004206295
DTC DETECTION LOGIC
NOTE:
• If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B210B is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the power supply position to start under the following conditions and wait for at least 1 second.
-
CVT selector lever is in the P or N position.
-
Depress the brake pedal
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
SEC-247, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206296
1.
INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4. Perform DTC Confirmation Procedure.
Is the DTC B210B displayed again?
YES
>> Replace IPDM E/R. Refer to
PCS-48, "Removal and Installation"
.
NO
>> Inspection End.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B210B
START CONT RLY
ON
IPDM E/R detects that the relay is stuck at ON po-
sition even if the following conditions are met for
about 1 second.
• Starter control relay ON/OFF signal from BCM
• Clutch interlock or shift park neutral position
(PNP) switch input signal
• IPDM E/R
SEC-248
< COMPONENT DIAGNOSIS >
[SEDAN WITH INTELLIGENT KEY]
B210C STARTER CONTROL RELAY
B210C STARTER CONTROL RELAY
Description
INFOID:0000000004206297
Starter control relay, integrated in IPDM E/R, permits the starter relay operation when in N or P position and
the steering is locked or unlocked. It is installed in parallel with the starter relay.
DTC Logic
INFOID:0000000004206298
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B210C is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the power supply position to start under the following conditions and wait for at least 1 second.
-
CVT selector lever is in the P or N position.
-
Depress the brake pedal
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
SEC-248, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206299
1.
INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4. Perform DTC Confirmation Procedure.
Is the DTC B210C displayed again?
YES
>> Replace IPDM E/R. Refer to
PCS-48, "Removal and Installation"
NO
>> Inspection End.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B210C
START CONT RLY
OFF
IPDM E/R detects that the relay is stuck at ON po-
sition even if the following conditions are met for
about 1 second.
• Starter control relay ON/OFF signal from BCM
• Clutch interlock or shift park neutral position
(PNP) switch input signal
• IPDM E/R
B210D STARTER RELAY
SEC-249
< COMPONENT DIAGNOSIS >
[SEDAN WITH INTELLIGENT KEY]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210D STARTER RELAY
Description
INFOID:0000000004206300
Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication.
DTC Logic
INFOID:0000000004206301
DTC DETECTION LOGIC
NOTE:
• If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B210D is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
• If DTC B210D is displayed with DTC B2617, first perform the trouble diagnosis for DTC B2617. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Ignition switch ON under the following conditions and wait for at least 1 second.
-
CVT selector lever is in the P or N position
-
Do not depress the brake pedal
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
SEC-249, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000004206302
1.
CHECK STARTER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Check voltage between IPDM E/R harness connector and
ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
NO
>> Check harness for open or short between IPDM E/R and
battery.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B210D
STARTER RELAY
ON
IPDM E/R detects that the relay is stuck at ON po-
sition even if the following conditions are met for
about 1 second.
• Starter control relay ON/OFF signal from BCM
• Clutch interlock or shift park neutral position
(PNP) switch input
• IPDM E/R
IPDM E/R
Ground
Voltage (V)
Connector
Terminal
E18
36
Ground
Battery voltage
ALKIA1319ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст