Nissan Altima L32. Instruction — part 1436
TM-88
< BASIC INSPECTION >
[CVT: RE0F09B]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Precaution for TCM
and CVT Assembly Replacement
INFOID:0000000004201627
CAUTION:
• Check if new data (Unit ID) are entered correctly after replacing CVT assembly and erasing data in
TCM. (Connect CONSULT-III, and then turn ignition switch OFF.)
• When replacing CVT assembly or TCM, refer to the pattern table below and erase the EEPROM in the
TCM if necessary.
EEPROM ERASING PATTERNS
METHOD FOR ERASING THE EEPROM IN THE TCM
1. Turn ignition switch ON.
2. Move selector lever to “R” position.
3. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
4. Press the brake pedal and turn the brake switch ON.
5. Press the accelerator pedal (0.5/8 - 4/8 throttle) not to exceed the half, and hold it in the half or less open
position. (This will set the closed throttle position signal to OFF and the wide open throttle position signal
to OFF.)
6. Perform “ERASE”.
7. Wait 3 seconds and then release the accelerator pedal.
8. Turn ignition switch OFF.
METHOD FOR WRITING DATA FROM THE ROM ASSEMBLY IN THE TRANSAXLE
In the following procedure, the TCM reads data from the ROM assembly and writes it to the EEPROM in the
TCM.
1. Erase the EEPROM in the TCM.
2. Move selector lever to “P” position.
3. Turn ignition switch ON.
CHECK METHOD
• Standard: About 2 seconds after the ignition switch ON, the CVT indicator lamp lights up for 2 seconds.
• Non-standard: Even after the ignition switch ON, the CVT indicator lamp does not light up after 2 seconds or
illuminates immediately.
CAUTION:
Perform in the “P” or “N” position.
Action for Non-standard
• Replace the CVT assembly.
• Replace the TCM.
CVT assembly
TCM
Erasing EEPROM in TCM
Remarks
Replaced
Replaced
Not required
Not required because the EEPROM in the TCM is in
the default state. (CVT assembly must be replaced
first.)
Not replaced
Replaced
Not required
Not required because the EEPROM in the TCM is in
the default state.
Replaced
Not replaced
Required
Required because data has been written in the EE-
PROM in the TCM and because the TCM cannot write
data from the ROM assembly in the transmission.
CVT SYSTEM
TM-89
< FUNCTION DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
FUNCTION DIAGNOSIS
CVT SYSTEM
System Diagram
INFOID:0000000004201628
JSDIA0074GB
TM-90
< FUNCTION DIAGNOSIS >
[CVT: RE0F09B]
CVT SYSTEM
Component Parts Location - Coupe
INFOID:0000000004201629
1.
Control device assembly (Instruction
mode select switch and instruction
mode position select switch)
2.
Accelerator pedal position (APP)
sensor
3.
Secondary speed sensor
4.
CVT unit harness connector
5.
TCM
6.
Battery
7.
Shift position indicator
Instruction mode indicator
AWDIA0166ZZ
CVT SYSTEM
TM-91
< FUNCTION DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Component Parts Location - Sedan
INFOID:0000000004201630
1.
Control device assembly (Instruction
mode select switch and instruction
mode position select switch)
2.
Accelerator pedal position (APP)
sensor
3.
Secondary speed sensor
4.
CVT unit harness connector
5.
TCM
6.
Battery
7.
Shift position indicator
Instruction mode indicator
AWIIA0001ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст