Nissan Altima L32. Instruction — part 761
FRONT DRIVE SHAFT
FAX-17
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Slide Joint Housing
• Make sure there are no compression scars, cracks or fractures or unusual wear of ball rolling surface.
• Make sure there is no damage to shaft screws.
• Make sure there is no deformation of boot installation parts.
Ball Cage
• Make sure there are no compression scars, cracks, fractures of sliding surface.
Steel Ball
• Make sure there are no compression scars, cracks, fractures or unusual wear.
Inner Race
• Check ball sliding surface for compression scars, cracks or fractures.
• Make sure there is no damage to serrated part.
CAUTION:
If there are any irregular conditions in the component, replace with a new set of joint sub-assembly,
ball cage, steel ball and inner race.
Damper
• Check damper for cracks or wear. Install damper with new damper bands.
ASSEMBLY
Transaxle Side
1. Install new boot and new small boot band on shaft.
CAUTION:
• Cover drive shaft serration with tape to prevent damage to
boot during installation.
2. Remove protective tape wound around serrated part of shaft.
3. Install spider assembly securely, making sure the matching marks which were made during disassembly
are properly aligned.
4. Install new snap ring using a suitable tool.
5. Pack drive shaft with specified amount of new grease (Genuine
NISSAN Grease or equivalent).
6. Install new stopper ring to housing of slide joint assembly.
7. After installation, pull shaft to check engagement between slide joint assembly and stopper ring.
SFA800
Grease amount
: 134 – 144 g (4.73 – 5.08 oz)
SFA023A
FAX-18
< DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
8. Install boot securely into grooves (indicated by * marks) as
shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Clean all
grease from surfaces.
9. Make sure boot installation length (L) is the length specified
below. Insert a flat-bladed screwdriver or similar tool into the
large end of boot. Bleed air from boot to prevent boot deforma-
tion.
CAUTION:
• Boot may break if boot installation length is less than standard value.
• Be careful that screwdriver tip does not contact inside surface of boot.
10. Secure large and small ends of boot with new boot bands as
shown.
CAUTION:
Discard old boot bands and replace with new ones.
11. Install new dust shield to slide joint housing.
12. After installing housing and shaft, make sure boot position is correct. If boot position is not correct, remove
old boot bands then reposition the boot and secure with new boot bands.
Wheel Side
1. Insert the amount of grease (Genuine NISSAN Grease or equiv-
alent) into joint sub-assembly serration hole until grease begins
to ooze from ball groove and serration hole. After inserting
grease, use a shop cloth to wipe off old grease that has oozed
out.
2. Cover serrated part of shaft with tape. Install new boot band and
boot to shaft. Be careful not to damage boot.
CAUTION:
Discard old boot band and boot; replace with new one.
3. Remove protective tape wound around serrated part of shaft.
Boot installation length (L)
: 167.9 mm (6.61 in)
SDIA1505E
SFA395
SDIA1127E
SFA800
FRONT DRIVE SHAFT
FAX-19
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
4. Attach new circlip to shaft. The circlip must fit securely into shaft
groove. Attach nut to joint sub-assembly.
Use a suitable tool to press-fit.
CAUTION:
Discard old circlip and replace with new one.
5. Insert the amount of new grease (Genuine NISSAN Grease or equivalent) listed below into housing from
large end of boot.
6. Install boot securely into grooves (indicated by * marks) as
shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
7. Make sure boot installation length (L) is the specified length indi-
cated below. Insert a flat-bladed screwdriver or similar tool into
the large end of boot. Bleed air from boot to prevent boot defor-
mation.
CAUTION:
• Boot may break if boot installation length is less than standard value.
• Be careful that screwdriver tip does not contact inside surface of boot.
8. Install new large and small boot bands securely using Tool.
NOTE:
Do not reuse boot bands.
CAUTION:
• Secure boot band so that dimension (M) meets specifica-
tion as shown.
9. After installing housing and shaft, rotate boot to check whether or not the actual position is correct. If boot
position is not correct, remove old boot bands then reposition the boot and secure with new boot bands.
RAC0049D
Grease amount
: 170 – 190 g (6.00 – 6.70 oz)
Boot installation length (L)
: 163 mm (6.42 in)
Tool number
: KV40107300 (
—
)
SDIA1505E
RAC1133D
Dimension (M)
: 1.0 – 4.0 mm (0.039 – 0.157 in)
DSF0047D
FAX-20
< DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
Damper
1. Use new damper bands for installation.
2. Install damper from stationary-joint side while holding it securely.
Disassembly and Assembly (Right Side)
INFOID:0000000004205634
DISASSEMBLY
Transaxle Side
1. Press shaft in a vise.
CAUTION:
When retaining shaft in a vise, always use copper or aluminum plates between vise and shaft.
2. Remove circlip and dust shield from slide joint housing.
3. Remove boot bands and slide the boots back.
(A)
: 205 – 215 mm (8.07 – 8.46 in)
(B)
: 70 mm (2.76 in)
SFA313B
1.
Joint sub-assembly
2.
Circlip
3.
Ball cage / Steel ball / Inner race assembly
4.
Boot bands
5.
Boot
6.
Shaft
7.
Damper bands
8.
Damper
9.
Boot band
10. Boot 11. Stopper
ring
12
Spider
assembly
13. Snap ring
14. Slide joint housing
15. Dust cover
16. Snap ring
17. Bearing
18. Retaining bracket (QR25DE engine)
19. Snap ring
20. Dust shield
21. Dust shield
22. Circlip
⇐
Front
WDIA0353E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст