Nissan Altima L32. Instruction — part 123
BCS-26
< FUNCTION DIAGNOSIS >
[BCM]
DIAGNOSIS SYSTEM (BCM)
*: The item is indicated, not monitored.
WIPER
WIPER : CONSULT - III Function
INFOID:0000000004202243
WORK SUPPORT
* : Factory setting
DATA MONITOR
ACTIVE TEST
FLASHER
CORNERING LAMP*
RH
—
LH
OFF
ILL DIM SIGNAL*
ON
—
OFF
Test item
Operation
Description
Service item
Setting item
Description
WIPER SPEED SET-
TING
ON
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper dial position)
OFF*
Without vehicle speed
(Front wiper intermittent time linked with the wiper dial position)
Monitor Item
[Unit]
Description
PUSH SW
Displays the status of the engine switch (push switch) judged by BCM.
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter with
CAN communication.
FR WIPER HI
[OFF/ON]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[OFF/ON]
FR WASHER SW
[OFF/ON]
FR WIPER INT
[OFF/ON]
FR WIPER STOP
[OFF/ON]
Displays the status of the front wiper auto stop signal received from IPDM E/R with
CAN communication.
INT VOLUME
[1
− 7]
Status of each switch judged by BCM using the combination switch reading function
Test item
Operation
Description
FRONT WIPER
HI
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LO
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF
Stops transmitting the front wiper request signal to stop the front wiper operation.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< FUNCTION DIAGNOSIS >
[BCM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FLASHER : CONSULT-III Function
INFOID:0000000004202244
Work support
* : Initial setting
Data monitor
Active test
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
INFOID:0000000004202246
WORK SUPPORT
Service item
Setting item
Setting
HAZARD ANSWER
BACK
LOCK ONLY*
Activated when locking.
Sets the hazard warning lamp answer back activation
when the door is lock/unlock with the request switch or
the key fob.
UNLK ONLY
Activated when unlock-
ing.
LOCK/UNLK
Activated when locking/
unlocking
OFF
Not activated
Monitor item
[Unit]
Description
TURN SIGNAL R
[ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L
[ON/OFF]
HAZARD SW
[ON/OFF]
The switch status input from the hazard warning switch
RKE LOCK
[ON/OFF]
The lock signal status received from the keyless receiver
RKE UNLOCK
[ON/OFF]
The unock signal status received from the keyless receiver
RKE PANIC
[ON/OFF]
The panic alarm signal status received from the keyless receiver
Test item
Operation
Description
FLASHER
RH
Blinks right turn signal lamp.
LH
Blinks left turn signal lamp.
OFF
Turns turn signal lamps (right and left) OFF.
Monitor item
Description
CONFIRM KEY FOB ID
It can be checked whether Intelligent Key ID code is registered or not in this mode.
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes
• MODE 3: 30 seconds
• MODE 4: 2 minutes
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch (driver side, passenger side and trunk) mode can
be changed to operate (ON) or not operate (OFF) with this mode.
ENGINE START BY I-KEY
Engine start function mode can be changed to operate (ON) or not operate (OFF) with this mode.
TRUNK/GLASS HATCH OPEN
Buzzer reminder function mode by trunk opener request switch can be changed to operate (ON)
or not operate (OFF) with this mode.
BCS-28
< FUNCTION DIAGNOSIS >
[BCM]
DIAGNOSIS SYSTEM (BCM)
SELF-DIAG RESULT
DATA MONITOR
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from the
following with this mode.
• 0.5 sec.
• 1.5 sec.
• OFF: Non-operation
PW DOWN SET
Unlock button pressing time on Intelligent Key button to lower front windows can be selected from
the following with this mode.
• 3 sec.
• 5 sec.
• OFF: Non-operation
TRUNK OPEN DELAY
Trunk button pressing time on Intelligent Key button can be selected from the following with this
mode.
• 0.5 sec.
• 1.5 sec.
• OFF: No delay
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operate (ON) or not operate (OFF)
with this mode.
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operate (ON) or not operate (OFF) with this mode.
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not op-
erate (OFF) with this mode.
HAZARD ANSWER BACK
Hazard reminder function mode can be selected from the following with this mode.
• LOCK ONLY: Door lock operation only
• UNLOCK ONLY: Door unlock operation only
• LOCK AND UNLOCK: Lock/unlock operation
• OFF: Non operation
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch (driver side and passenger
side) can be selected from the following with this mode.
• HORN CHIRP: Sound horn
• BUZZER: Sound Intelligent Key warning buzzer
• OFF: Non-operation
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to op-
erate (ON) or not operate (OFF) with this mode.
SHORT CRANKING OUTPUT
Starter motor can operate during the times below.
• 70 msec
• 100 msec
• 200 msec
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis.
Monitor item
Description
Monitor Item
Condition
REQ SW-DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW-AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW-BD/TR
Indicates [ON/OFF] condition of trunk opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push button ignition switch.
IGN RLY2-F/B
Indicates [ON/OFF] condition of ignition relay 2.
ACC RLY1-F/B
Indicates [ON/OFF] condition of accessory relay.
CLUTCH SW
NOTE:
This item is displayed, but cannot be monitored.
BRAKE SW 1
Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW
Indicates [ON/OFF] condition of P position.
SFT PN/N SW
Indicates [ON/OFF] condition of P or N position.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-29
< FUNCTION DIAGNOSIS >
[BCM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
S/L -LOCK
Indicates [ON/OFF] condition of steering lock (LOCK).
S/L -UNLOCK
Indicates [ON/OFF] condition of steering lock (UNLOCK).
S/L RELAY-F/B
Indicates [ON/OFF] condition of ignition switch.
UNLK SEN-DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push button ignition switch from IPDM E/R via CAN.
IGN RLY1-F/B
Indicates [ON/OFF] condition of ignition relay 1 from IPDM E/R via CAN.
DETE SW -IPDM
Indicates [ON/OFF] condition of P position from TCM via CAN.
SFT PN -IPDM
Indicates [ON/OFF] condition of P or N position from TCM via CAN.
SFT P -MET
Indicates [ON/OFF] condition of P position from TCM via CAN.
SFT N -MET
Indicates [ON/OFF] condition of N position from IPDM E/R via CAN.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states from ECM via CAN.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock (LOCK) request from IPDM E/R via CAN.
S/L UNLOCK-IPDM
Indicates [ON/OFF] condition of steering lock (UNLOCK) request from IPDM E/R via CAN.
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay from IPDM E/R via CAN.
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status.
ID OK FLAG
Indicates [SET/RESET] condition of key ID.
PRMT ENG STRT
Indicates [SET/RESET] condition of engine start possibility.
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the
numerical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk lid.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation.
Intelligent Key warning buzzer sounds when “ON” on CONSULT-III screen is touched.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст