Nissan Altima L32. Instruction — part 1187
RF-90
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000004205555
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000004205556
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
(Kent-Moore No.)
Description
Engine ear
(J-39565)
Locating the noise
Power tools
Loosening bolts, nuts and screws
SIIA0995E
PIIB1407E
SUNROOF UNIT ASSEMBLY
RF-91
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
ON-VEHICLE REPAIR
SUNROOF UNIT ASSEMBLY
Inspection
INFOID:0000000004205557
WIND DEFLECTOR
1. Open glass lid assembly fully.
2. Visually check for proper installation, damaged/deteriorated components, or foreign objects within mecha-
nism. Correct as required for smooth operation.
3. Check for grease at the wind deflector arm (1) and pivot areas. If
necessary, apply a sufficient amount of grease for non-binding
operation.
⇐:Vehicle front
4. Check that the wind deflector (1) moves freely within the sunroof
unit assembly while instructionly pressing down and releasing. If a
malfunction is detected, remove the sunroof unit assembly and
visually inspect; refer to
replace either wind deflector (1) or sunroof unit assembly as
required.
⇐:Vehicle front
LINK AND WIRE ASSEMBLY
NOTE:
Before replacing a suspect part, make sure it is the source of noise being experienced.
1. Check link to determine if coating film has peeled off excessively enough that substrate is visible. Check
also to determine if link is the source of noise. Replace as necessary.
2. Visually check to determine if a sufficient amount of grease has been applied to wire or rail groove. If not,
add grease as required.
3. Check wire for any damage or deterioration. If any damage is found, replace sunroof unit assembly.
WEATHERSTRIP
1. Visually check weatherstrip for damage, deterioration, or deformation.
• Open glass lid assembly partially to inspect front edge of weatherstrip.
• Tilt up glass lid assembly fully to inspect sides and rear edge of weatherstrip.
If any area of the weatherstrip is found to be damaged, replace the glass lid assembly. Refer to
2. Check for leakage around glass lid assembly.
• Close glass lid assembly.
• Pour water around surface to determine area of concern.
- For gaps or misalignment, adjust glass lid assembly to specifications. Refer to
.
- For damaged sealing surfaces, either replace glass lid assembly
RF-95, "Removal and Installation"
, or
repair the panel
BRM-30, "High Strength Steel (HSS)"
.
DRAIN HOSES
LIIA2336E
WIIA0849E
RF-92
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
Sedan Models
Coupe Models
ALKIA1374ZZ
1.
Drain hose front RH
2.
Drain hose front LH
3.
Drain hose rear LH
4.
Drain hose rear RH
5.
Sunroof unit assembly
6.
Fascia
7.
Seal
8.
Fender
9.
Drain hose
⇐
Vehicle front
AWKIA0173ZZ
SUNROOF UNIT ASSEMBLY
RF-93
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
1. Remove the headlining. For Sedan Refer to
INT-42, "Removal and Installation"
. For Coupe Refer to
20, "Removal and Installation"
2. Visually check drain hoses for:
• Proper connection at sunroof unit assembly drain hose connector(s).
• Damage, pinch, cracks, deterioration.
• Proper fastening and routing on body panels.
3. Pour water through drain hoses to determine watertight performance.
If damaged or leaking portions in any drain hose is found, replace entire drain hose as necessary.
ADJUSTMENT
CAUTION:
• Always work with a helper.
• Handle glass lid assembly with care to prevent damage.
NOTE:
• For easier and more accurate installation, always mark each point before removal.
• After any adjustment, check sunroof operation and glass lid assembly alignment.
1.
Drain hose front RH
2.
Drain hose front LH
3.
Drain hose rear LH
4.
Drain hose rear RH
5.
Sunroof unit assembly
6.
Fascia
7.
Seal
8.
Fender
9.
Drain hose
⇐
Vehicle front
ALKIA0065ZZ
1.
Roof
2.
Weatherstrip
3.
Glass lid assembly
A.
Front edge specifications
B.
Side edge specifications
C.
Rear edge specifications
D.
Weatherstrip overlap tolerance
E.
Weatherstrip width dimension
F.
Surface flushness tolerance
(Glass lid below roof line)
Vehicle front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст