Nissan Altima L32. Instruction — part 1188
RF-94
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
Unit: mm (in)
Gap adjustment (A-A, C-C)
1. Open sunshade assembly (1).
2. Tilt glass lid assembly up, then release side trim covers (2) and set aside.
3. Loosen glass lid assembly bolts (A) (two each on left and right
sides), then tilt glass lid assembly down.
4. Instructionly adjust glass lid assembly from outside of vehicle so
gaps A-A and C-C are within specifications.
NOTE:
Temporarily snug glass lid assembly bolts to prevent movement
between each adjustment.
5. Tilt glass lid assembly up and down several times using sunroof
switch to check that it operates smoothly.
6. Tilt glass lid assembly up and tighten bolts to specification.
NOTE:
First tighten left front bolt, then right rear bolt on glass lid assem-
bly to prevent uneven torque while tightening remaining bolts.
7. Attach side trim cover, then tilt glass lid assembly down.
Gap Adjustment (B-B)
1. Remove headlining. For Sedan Refer to
INT-42, "Removal and Installation"
2. Loosen sunroof unit assembly and sunroof side bracket bolts.
3. Carefully slide sunroof unit assembly side to side or add shims until gap is within specifications.
NOTE:
Temporarily snug sunroof unit assembly bolts to prevent movement between each adjustment.
4. Tilt glass lid assembly up and down several times using sunroof switch to check that it operates smoothly.
5. Tighten sunroof unit assembly and sunroof side bracket bolts.
NOTE:
First tighten left front sunroof unit assembly bolt, then right rear to prevent uneven torque while tightening
remaining bolts.
6. Install headlining. For Sedan Refer to
INT-42, "Removal and Installation"
Height Adjustment
1. Tilt glass lid assembly up and down several times using sunroof switch to check that it operates smoothly.
2. Check height difference between roof surface and glass lid assembly surface, then compare to specifica-
tions.
3. If necessary, adjust height difference by using the following procedure.
• Loosen glass lid assembly bolts.
• Instructionly raise/lower glass lid assembly until height difference is within specification.
NOTE:
If necessary, shims may be added between sunroof unit assembly and roof to increase adjustment
range. Refer to
Temporarily snug sunroof unit assembly bolts to prevent movement between each adjustment.
• Tilt glass lid assembly up and down several times using sunroof switch to check that it operates
smoothly.
• Tighten glass lid assembly and sunroof side bracket bolts.
NOTE:
First tighten left front bolt, then right rear bolt on glass lid assembly to prevent uneven torque while tight-
ening remaining bolts.
• After any adjustment, check sunroof operation and glass lid assembly alignment.
A-A
B-B
C-C
D.
1.4
± 0.45 (0.06 ± 0.02)
1.4
± 0.45 (0.06 ± 0.02)
1.4
± 0.45 (0.06 ± 0.02)
E.
5.8
± (0.23)
5.8
± (0.23)
5.8
± (0.23)
F.
-0.8
± 1.5 (-0.03 ± 0.06)
-0.8
± 1.5 (-0.03 ± 0.06)
-0.8
± 1.5 (-0.03 ± 0.06)
ALKIA0059ZZ
SUNROOF UNIT ASSEMBLY
RF-95
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Exploded View
INFOID:0000000004205558
Removal and Installation
INFOID:0000000004205559
CAUTION:
• After installing either sunroof unit assembly or glass lid assembly, check gap/height adjustments
and operation to make sure there is no malfunction.
• Always work with a helper.
• Handle glass lid assembly with care to prevent damage.
• When taking sunroof unit out, use shop cloths to protect the seats and trim from damage.
SUNROOF UNIT ASSEMBLY
Removal
1. Close glass lid assembly.
2. Remove headlining. Refer to
INT-20, "Removal and Installation"
3. Disconnect drain hoses.
1.
Glass lid assembly
2.
Sunshade
3.
Wind deflector
4.
Sunroof motor assembly
5.
Sunroof side bracket
6.
Drain hose connector
7.
Sunshade stopper
8.
Sunroof unit assembly
A.
Bolt
B.
Screw
C.
Nut
Vehicle front
ALKIA0061ZZ
RF-96
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
4. Remove screws (A), then pull sunroof switch bracket (1) away
from sunroof unit assembly (2).
Vehicle front
5. Disconnect sunroof motor harness connector.
6. Remove bolts on the front end and side rails of the sunroof unit
assembly.
7. Remove front sunroof side bracket bolts.
8. Remove rear sunroof side bracket bolts and remove sunroof unit
assembly from roof panel.
9. Remove sunroof unit assembly through the passenger compart-
ment while being careful not to damage the seats and trim.
Installation
1. Loosely tighten the rear sunroof side bracket bolts to the sunroof unit assembly side rails.
2. Bring sunroof unit into passenger compartment and loosely tighten rear sunroof side bracket bolts to roof
panel while supporting front.
3. Align the sunroof unit assembly front end rail and side rails with the locator pins, then loosely tighten the
bolts.
4. Install remaining sunroof side brackets and loosely tighten bolts.
5. Tighten the sunroof unit assembly front end and side rail bolts diagonally to the specified torque.
6. Tighten the front sunroof side bracket bolts at the vehicle side first, then at the side rail end.
7. Tighten the rear sunroof side bracket bolts at the vehicle side first, then at the side rail end.
8. Connect sunroof motor harness connector.
9. Install sunroof switch bracket.
10. Connect drain hoses.
11. Install headlining. For Sedan Refer to
INT-42, "Removal and Installation"
GLASS LID ASSEMBLY
Removal
1. Open sunshade (1), then close glass lid assembly.
Vehicle front
2. Slide the side trim covers (2) RH/LH inward, then release them
from the glass lid assembly inside edge and set aside.
3. Remove the bolts (A) on the left and right sides and glass lid
assembly from sunroof unit assembly.
Installation
1. Position glass lid assembly to sunroof unit assembly.
2. Tighten glass lid assembly bolts to specification.
ALKIA0060ZZ
PIIB4747J
ALKIA0059ZZ
SUNROOF UNIT ASSEMBLY
RF-97
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
NOTE:
First tighten left front bolt, then right rear bolt on glass lid assembly to prevent uneven torque while tight-
ening remaining bolts.
3. Slide side trim covers onto inside edge of glass lid assembly.
4. After installation, check sunroof operation and glass lid assembly alignment. Refer to
.
SUNSHADE
Removal
1. Remove sunroof unit assembly. Refer to
.
2. Remove glass lid assembly. Refer to
RF-95, "Removal and Installation"
.
3. Remove the sunshade stoppers (1) RH/LH from the sunroof unit
assembly side rails (2).
⇐ Vehicle front
4. Slide sunshade rearward past sunroof unit assembly side rail
ends to remove.
Installation
Installation is in the reverse order of removal.
SUNROOF MOTOR
Removal
1. Close glass lid assembly.
2. Disconnect the negative and positive battery terminals.
3. Remove the room/map lamp assembly from headliner (4). For
Sedan Refer to
INL-121, "Removal and Installation"
. For Coupe
INL-121, "Removal and Installation"
⇐ Vehicle front
4. Remove sunroof motor screws (A).
5. Disconnect harness connector (2) and remove sunroof motor (1)
from sunroof unit assembly front end rail.
CAUTION:
Never run the removed sunroof motor as a single unit.
Installation
Installation is in the reverse order of removal.
CAUTION:
Before installing the motor, be sure to place the link and wire assembly in the symmetrical and fully
closed position.
• During motor installation, move sunroof motor laterally little by little so that the gear is completely engaged
into the wire on the sunroof unit assembly, and the mounting surfaces become parallel. Install the sunroof
motor screws, then tighten.
• NOTE:
If necessary, insert a suitable tool into the drive key (3) and rotate right or left slightly to assist in complete
sunroof motor gear alignment.
• Synchronize sunroof motor with sunroof unit assembly. Refer to
RF-15, "SUNROOF MOTOR ASSEMBLY :
LIIA2347E
ALKIA0057ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст