Nissan Altima L32. Instruction — part 1391
STEERING GEAR AND LINKAGE
ST-17
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000004204021
Removal and Installation
INFOID:0000000004204022
REMOVAL
1. Remove the front tires.
2. Remove undercover using power tool.
3. Remove lower side bolt of lower joint.
4. Remove cotter pin (1), and then loosen the nut.
5. Remove steering outer socket (2) from steering knuckle (3) so
as not to damage ball joint boot (4) using the Tool.
CAUTION:
Temporarily tighten the nut to prevent damage to threads
and to prevent the Tool from suddenly coming off.
6. Remove high and low pressure piping of hydraulic piping, and
then drain power steering fluid. Refer to
7. Remove steering hydraulic piping bracket from front suspension
member.
8. Remove SSPS valve harness connector. Refer to
9. Remove bolts and nuts of steering gear assembly, and then remove steering gear assembly from vehicle.
1.
Cotter pin
2.
Steering gear assembly
⇐
Front
AWGIA0006GB
SGIA0844E
Tool number
: HT72520000 (J-25730-A)
SGIA1183E
ST-18
< ON-VEHICLE REPAIR >
STEERING GEAR AND LINKAGE
INSPECTION AFTER REMOVAL
Check for fluid leaks or damage to steering gear. If any exist, replace steering gear as an assembly.
INSTALLATION
Installation is in the reverse order of removal. For tightening specifications, refer to
.
• When installing lower joint to steering gear assembly, follow the procedure listed below.
- Set rack of steering gear in the neutral position.
NOTE:
To get the neutral position of rack, turn gear-sub assembly and measure the distance of inner socket, and
then measure the intermediate position of the distance.
- Align rear cover cap projection (A) with the marking position (B) of
gear housing assembly.
- Install slit part of lower joint (C) aligning with the projection (A) of
rear cover cap (1). Make sure that the slit part of lower joint (C) is
aligned with both the projection (A) of rear cover cap (1) and the
marking position (B) of gear housing assembly.
• After installation, bleed air from the steering hydraulic system.
• Perform final tightening of nuts and bolts on each part under
unladen conditions with tires on level ground when removing steer-
ing gear assembly. Check wheel alignment. Refer to
.
INSPECTION AFTER INSTALLATION
Make sure that steering wheel operates smoothly by turning several times from full left stop to full right stop.
SGIA1175E
POWER STEERING OIL PUMP
ST-19
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
POWER STEERING OIL PUMP
QR25DE
QR25DE : Exploded View
INFOID:0000000004204023
QR25DE : Removal and Installation
INFOID:0000000004204024
REMOVAL
1. Drain power steering fluid from reservoir tank.
2. Remove undercover using power tool.
3. Loosen drive belt. Refer to
EM-16, "Removal and Installation"
.
4. Remove drive belt from oil pump pulley.
5. Remove piping of high pressure and low pressure (drain fluid from pipings). Refer to
.
6. Remove oil pump bolts, and then remove power steering oil pump. Refer to
.
INSPECTION AFTER REMOVAL
INSTALLATION
Installation is in the reverse order of removal. For tightening specifications, refer to
.
• Perform the following procedure after installing.
- For the installation of drive belt, refer to
.
- Bleed air. Refer to
VQ35DE
1.
Rear bracket
2.
Pump assembly
3.
Front bracket
ALGIA0005GB
ST-20
< ON-VEHICLE REPAIR >
POWER STEERING OIL PUMP
VQ35DE : Exploded View
INFOID:0000000004204025
VQ35DE : Removal and Installation
INFOID:0000000004204026
REMOVAL
1. Drain power steering fluid from reservoir tank.
2. Remove undercover using power tool.
3. Loosen drive belt. Refer to
EM-121, "Removal and Installation"
.
4. Remove drive belt from oil pump pulley.
5. Remove piping of high pressure and low pressure (drain fluid from pipings). Refer to
ST-24, "VQ35DE : With 18 Inch Tire"
.
6. Remove oil pump bolts, and then remove power steering oil pump. Refer to
.
INSPECTION AFTER REMOVAL
INSTALLATION
Installation is in the reverse order of removal.
• When installing power steering oil pump, install all bolts by hand initially, then tighten bolts to specification.
• Perform the following procedure after installing.
- Adjust belt tension. Refer to
.
- Bleed air. Refer to
1.
Rear bracket
2.
Pump assembly
3.
Front bracket
AWGIA0099GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст