Nissan Altima L32. Instruction — part 1390
STEERING WHEEL
ST-13
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
ON-VEHICLE REPAIR
STEERING WHEEL
Removal and Installation
INFOID:0000000004204018
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1. Set vehicle to the straight-ahead position.
2. Remove driver air bag module. Refer to
SR-5, "Removal and Installation"
3. Remove steering wheel lock nut after steering is locked.
4. Remove steering wheel using Tool (A).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Align the spiral cable. Refer to
SR-8, "Removal and Installation"
.
Tool number A: ST27180001 (J-25726-A)
AWGIA0004GB
ST-14
< ON-VEHICLE REPAIR >
STEERING COLUMN
STEERING COLUMN
Exploded View
INFOID:0000000004513205
Removal and Installation
INFOID:0000000004513206
REMOVAL
Hole Cover Seal, Hole Cover and Lower Shaft Assembly
1. Set wheels to the straight-ahead position.
• Steering gear (2)
2. Remove lower side bolt (A) of lower shaft assembly (1).
1-4.
Steering column assembly nut tight-
ening order
5.
Steering wheel
6.
Combination switch and spiral cable
7.
Steering column assembly
8.
Hole cover seal
9.
Herbie clip
10.
Hole cover
11. Lower shaft assembly
AWGIA0105GB
ALGIA0041ZZ
STEERING COLUMN
ST-15
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
3. Remove bolt (A) and nut (B) of column upper joint (2), then
remove lower shaft assembly (1).
4. Loosen herbie clip, then remove hole cover seal from hole
cover.
5. Remove nuts of hole cover, and then remove clamp and hole
cover from dash panel.
Steering Column Assembly
1. Set wheels to the straight-ahead position.
2. Remove driver air bag module. Refer to
SR-5, "Removal and Installation"
3. Remove steering wheel. Refer to
ST-13, "Removal and Installation"
.
4. Remove instrument lower cover (LH). Refer to
.
5. Remove knee protector bolts, then remove knee protector (1).
6. Remove steering column cover (upper and lower). Refer to
7. Remove combination switch and spiral cable. Refer to
8. Disconnect each switch connector installed to steering column
assembly, and then disconnect harness from steering column
assembly.
• Lower shaft assembly (1)
9. Remove bolt (A) and nut (B) of column upper joint (2).
10. Remove steering column assembly and nuts, then remove
steering column assembly.
INSPECTION AFTER REMOVAL
Hole Cover Seal, Hole Cover and Lower Shaft Assembly
Check each part of hole cover seal, hole cover and steering column and lower shaft assembly for damage or
other malfunctions. Replace if necessary.
Steering Column Assembly
• Check each part of steering column assembly for damage or other malfunctions. Replace entire steering col-
umn assembly if any parts are damaged.
ALGIA0042ZZ
ALGIA0043ZZ
ALGIA0042ZZ
ST-16
< ON-VEHICLE REPAIR >
STEERING COLUMN
• Measure the length (L) as shown if vehicle has been involved in a
minor collision. Replace steering column assembly if outside the
specifications.
• Measure steering column rotating torque using Tool. Replace steering column assembly if outside the stan-
dard.
• Check tilt and telescopic mechanism operating range (L
1
), (L
2
) as
shown.
INSTALLATION
Steering Column Assembly
Installation is in the reverse order of removal.
Hole Cover Seal, Hole Cover and Lower Shaft Assembly
Installation is in the reverse order of removal.
• When installing lower shaft assembly to steering gear assembly, follow the procedure listed below.
- Set rack of steering gear in the neutral position.
NOTE:
To get the neutral position of rack, turn gear sub-assembly and measure the distance of inner socket, and
then measure the intermediate position of the distance.
- Align rear cover cap projection (A) with the marking position (B) of
gear housing assembly.
- Install slit part of lower shaft assembly (C) aligning with the projec-
tion (A) of rear cover cap (1). Make sure that the slit part of lower
shaft assembly (C) is aligned with both the projection (A) of rear
cover cap (1) and the marking position (B) of gear housing assem-
bly.
- Perform final tightening of nuts and bolts on each part under
unladen conditions with tires on level ground when removing steer-
ing gear assembly. Check wheel alignment. Refer to
.
Steering column length (L)
: Refer to
SGIA1177E
Tool number
: ST3127S000 (J-25765-A)
Rotating torque
: Refer to
Tilt operating range (L
1
)
: Refer to
Telescopic operating range
(L
2
)
: Refer to
SGIA1179E
SGIA1175E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст